YASKAWA Z1000 CIMR-ZU*A Series Programming Manual page 334

Index
Middle Output Frequency Voltage 2 ...........................................65
Minimum KEB Time........................................................... 104
Minimum Output Frequency ....................................................65
Minimum Output Frequency Voltage..........................................65
Minimum Wait Time for Sending Messages.................... 255, 295, 311
Momentary Power Loss Minimum Baseblock Time................. 103, 214
Momentary Power Loss Operation Selection ...........................34, 213
Momentary Power Loss Ride-Thru .......................................... 102
Momentary Power Loss Ride-Thru Time ............................. 103, 213
Momentary Power Loss Voltage Recovery Ramp Time ............ 103, 214
Monitor Parameters.........................................................96, 232
Most Recent Fault .............................................................. 234
Motor Acceleration Time for Inertia Calculations ................... 109, 215
Motor Base Frequency ................................................... 154, 230
Motor Base Speed ........................................................ 155, 230
Motor d-Axis Current at Previous Fault ..................................... 234
Motor d-Axis Inductance ........................................................68
Motor Direction at Power Up when Using Operator................. 132, 222
Motor Excitation Current (ld) ................................................. 238
Motor Induction Voltage Constant 1 ...........................................69
Motor Induction Voltage Constant 2 ...........................................69
Motor Iron Loss ........................................................... 155, 230
Motor Iron Loss for Torque Compensation ...................................67
Motor Line-to-Line Resistance .................................................67
Motor No-Load Current..........................................................66
Motor Overheat Alarm Operation Selection .......................... 101, 213
Motor Overheat Fault Operation Selection............................ 101, 213
Motor Overload Alarm...........................................................89
Motor Overload Estimate (oL1) .............................................. 236
Motor Overload Protection Selection ....................................89, 213
Motor Overload Protection Time ....................................... 100, 213
Motor Pre-Heat 1 .................................................................79
Motor Pre-Heat 2 .................................................................79
Motor Pre-Heat Current 2 .......................................................30
Motor Protection ..................................................................99
Motor Protection Using a PTC Thermistor.................................. 100
Motor PTC Characteristics .................................................... 101
Motor q-Axis Current at Previous Fault ..................................... 234
Motor q-Axis Inductance ........................................................68
Motor Rated Current ............................................ 66, 68, 154, 230
Motor Rated Power .............................................. 67, 68, 154, 230
Motor Rated Slip..................................................................66
Motor Rated Voltage ..................................................... 154, 230
Motor Secondary Current (Iq) ................................................ 238
Motor Stator Resistance..........................................................68
Motor Temperature Input Filter Time.................................. 102, 213
Motor Underload Protection Level at Minimum Frequency ........ 116, 217
Motor Underload Protection Selection................................. 116, 217
Multi-Function Analog Inputs ..................................................92
Multi-Function Analog Input Terminal Settings .............................92
Multi-Function Analog Outputs ................................................96
Multi-Function Analog Output Terminal AM Bias ..........................97
Multi-Function Analog Output Terminal AM Gain..........................97
Multi-Function Analog Output Terminal AM Monitor Selection..........97
Multi-Function Analog Output Terminal AM Signal Level Selection ....98
Multi-Function Analog Output Terminal FM Bias...........................97
Multi-Function Analog Output Terminal FM Gain ..........................97
Multi-Function Analog Output Terminal FM Monitor Selection ..........97
Multi-Function Analog Output Terminal FM Signal Level Selection.....98
Multi-Function Digital Inputs ...................................................72
334
Multi-Function Digital Outputs .................................................82
Multi-Step Speed Reference.....................................................73
N
N2 Serial Communication ..................................................... 288
N2 Setup Parameters ........................................................... 288
N2 Specifications ............................................................... 285
NetRef/ComRef Function Selection............................................70
Network Termination ........................................ 248, 271, 287, 306
Number of Auto Restart Attempts...................................... 112, 216
Number of Motor Poles ......................................... 67, 68, 154, 230
Number of PM Motor Poles ................................................... 156
Number of Run Commands ................................................... 236
Number of Run Commands Counter Initialization................... 134, 223
Number of Speed Search Restarts ..............................................35
O
OFF Key Function Selection .................................................. 222
Offset Frequencies........................................................... 61, 79
Offset Frequency................................................................ 238
oH Pre-Alarm Time Limit .......................................................90
oL1 Current Level .............................................................. 213
oL2 Characteristics Selection at Low Speeds......................... 120, 218
oPE Fault Parameter............................................................ 233
Operation Selection when HOA Keypad is Disconnected .......... 132, 222
Operation Status Monitors..................................................... 158
Operator Related Settings...................................................... 128
Option Frequency Reference .................................................. 236
Option Monitors 1 to 20 ....................................................... 238
Option Settings....................................................................70
Output Current .................................................................. 232
Output Current 1 during Speed Search ........................................35
Output Current at Previous Fault ............................................. 233
Output Frequency............................................................... 232
Output Frequency after Soft Start ............................................ 233
Output Frequency at Previous Fault.......................................... 233
Output Frequency Reduction During Overheat Alarm .................... 118
Output Ground Fault Detection Selection ............................. 119, 218
Output Phase Loss Detection Lvl for Dynamic Noise Control ........... 153
Output Phase Loss Protection ................................................. 218
Output Phase Loss Protection Selection ..................................... 119
Output Power.................................................................... 232
Output Power at Previous Fault............................................... 234
Output Terminal Status ........................................................ 232
Output Terminal Status at Previous Fault ................................... 234
Output Voltage at Previous Fault ............................................. 234
Output Voltage Limit........................................................... 127
Output Voltage Reference ..................................................... 232
Output Voltage Reference (Vd)............................................... 238
Output Voltage Reference (Vq)............................................... 238
ov2 Detect Time ................................................................ 153
Overcurrent Detection Gain ............................................. 120, 218
Overexcitation Deceleration................................................... 107
Overexcitation Deceleration Gain ...................................... 125, 219
Overexcitation Operation Selection .................................... 125, 219
Overheat Alarm Level.................................................... 117, 217
Overheat Pre-Alarm Operation Selection ...............................90, 217
Overtorque Detection Operation.............................................. 114
Overvoltage Suppression Function ........................................... 108
Overvoltage Suppression Function Selection ............................... 108
YASKAWA SIEP YAIZ1U 03B YASKAWA AC Drive – Z1000 Programming Manual