YASKAWA Z1000 CIMR-ZU*A Series Programming Manual page 332

Index
Control Mode.................................................................... 232
Control Mode Dependent Parameter Default Values ...................... 239
Cooling Fan Maintenance ..................................................... 236
Cooling Fan Maintenance Setting (Operation Time) ...................... 223
Cooling Fan Operation Time.................................................. 236
Cooling Fan Operation Time Setting......................................... 133
Cooling Fan Replacement ............................................... 171, 172
Copy Allowed Selection ....................................................... 133
Copy Function................................................................... 132
Copy Function Selection....................................................... 132
CRC-16 .......................................................................... 312
CRC-16 Checksum Calculation Example ................................... 313
Cumulative Operation Time................................................... 236
Cumulative Operation Time at 5th Most Recent Fault .................... 234
Cumulative Operation Time at Most Recent Fault ......................... 234
Cumulative Operation Time at Previous Fault.............................. 234
Cumulative Operation Time Selection................................. 133, 223
Cumulative Operation Time Setting ................................... 133, 223
Current Control Gain during Speed Search (Speed Estimation Type).....35
Current Fault .................................................................... 233
Current Unbalance Detection (LF2).................................... 120, 218
Customer Safeties.................................................................82
Cyclic Redundancy Check..................................................... 312
D
Daily Inspection................................................................. 163
d-Axis Current for High Efficiency Control ................................ 126
DC Bus Pre-Charge Relay Maintenance Setting ........................... 133
DC Bus Undervoltage ............................................................86
DC Bus Voltage................................................................. 232
DC Bus Voltage Adjustment Gain ..................................... 109, 215
DC Bus Voltage at Previous Fault............................................ 234
DC Bus Voltage Setpoint during KEB....................................... 104
DC Injection Braking Current...................................................30
DC Injection Braking Start Frequency.........................................29
DC Injection Braking Time at Start ............................................30
DC Injection Braking Time at Stop ............................................30
Deceleration Rate Calculation Gain.......................................... 215
Deceleration Time ................................................................51
Deceleration Time at Stall Prevention during Acceleration......... 105, 215
Defaults by Drive Model Selection (o2-04)................................. 131
Desired DC Bus Voltage during KEB ....................................... 214
Device Object ................................................................... 260
Digital Outputs ....................................................................82
Direction Command for 2-Wire Seq. 2 ........................................78
Drive/kVA Selection ........................................................... 222
Drive Cooling Fans ............................................................. 164
Drive Delay Time Setting .......................................................28
Drive Enable.................................................................. 80, 90
Drive Enable2 .....................................................................81
Drive Model Selection ......................................................... 131
Drive Mode Unit Monitor Selection ......................................... 128
Drive Operations by BACnet ................................................. 254
Drive Operations by N2........................................................ 292
Drive Operation Status at Previous Fault.................................... 234
Drive Overheat Alarm............................................................90
Drive Overheat Alarm (oH2)....................................................74
Drive Overheat Pre-Alarm.......................................................89
Drive Ready .......................................................................85
Drive Slave Address................................................ 250, 288, 307
332
Drive Status...................................................................... 233
Drive Transmit Wait Time ........................................ 251, 289, 308
During Baseblock.................................................................89
During Baseblock (N.O.) ........................................................86
During Fast Stop ..................................................................90
During Frequency Output........................................................89
During KEB Operation...........................................................90
During Run ........................................................................83
During Short Circuit Braking ...................................................90
During Speed Search .............................................................90
Dynamic Audible Noise Control Function Selection ...................... 224
Dynamic Audible Noise Control Selection.................................. 135
Dynamic Noise Control Function ............................................ 135
E
Emergency Override ........................................................... 145
Emergency Override Forward Run.............................................82
Emergency Override Reverse Run .............................................82
Enabling Programmable Bypass Logic ...................................... 144
Energy Saving Coefficient Value...............................................50
Energy Saving Control Selection ...............................................49
Energy Savings Mode .......................................................... 148
Enter Command........................................................... 252, 328
Enter command necessary ......................................... 252, 290, 309
Enter command not necessary .................................... 252, 290, 309
Enter Command Types................................................... 261, 328
External Fault .....................................................................77
External Fault from Comm. Option Detection Selection....................70
External Fault from Comm. Option Operation Selection ...................70
External Speed Search Command ..............................................79
F
F1/F2 Key Function Selection ................................................ 130
Fast Stop (N.O., N.C.) ...........................................................76
Fast Stop Time ....................................................................52
Fault History..................................................................... 158
Fault Reset .........................................................................76
Fault Reset Command Active ...................................................87
Fault Reset Interval Time................................................ 113, 216
Fault Reset Operation Selection ........................................ 114, 216
Fault Restart .......................................................................89
Fault Trace....................................................................... 158
Field Weakening ............................................................. 60, 79
Field Weakening Frequency Limit .............................................60
Field Weakening Level ..........................................................60
Forward Jog .......................................................................76
Forward Run Command for 2-Wire Seq. ......................................78
Frequency Detection 1 ...........................................................84
Frequency Detection 2 ...........................................................85
Frequency Detection 3 ...........................................................88
Frequency Detection 4 ...........................................................88
Frequency Gain at KEB Start ................................................. 103
Frequency Reduction Rate during Overheat Pre-Alarm............. 118, 218
Frequency Reference .......................................................56, 232
Frequency Reference at Previous Fault ...................................... 233
Frequency Reference at Reference Loss............................... 111, 216
Frequency Reference from MEMOBUS/Modbus Comm. ................ 236
Frequency Reference Hold Function Selection ...............................59
Frequency Reference Loss.......................................................86
Frequency Reference Loss Detection Selection ........................86, 216
YASKAWA SIEP YAIZ1U 03B YASKAWA AC Drive – Z1000 Programming Manual