Table of Contents
Advertisement
Immunity to Conducted Disturbance by RF fields, injected
Current
EN 61000-6-2, IEC 60255-22-6
Power system frequency magnetic field
EN 61000-6-2, IEC 61000-4-8
Radiated Electromagnetic Interference
IEEE Std C37.90.2
Power frequency on binary input ports
IEC 60255-26, IEC 61000-4-16
Ripple on d.c. input power port inmunity test, IEC 61000-4-17
Gradual shutdown / start-up for d.c. power supply
IEC 60255-26
EMC Tests for Noise Emission (Type Test)
Standard:
Radio noise voltage to lines, only auxiliary voltage
IEC/CISPR 16-2-1
Interference field strength
IEC/CISPR 16-2-3
Harmonic currents on the network lead at AC 230 V
IEC 61000-3-2
Voltage dips, interruptions and fluctuations
IEC 60255-11, IEC 61000-4-29
Mechanical Tests
4.1.6
Vibration and Shock Stress during Steady-State Operation
Standards:
Oscillation
IEC 60255-21-1, Class 2;
IEC 60068-2-6
Shock
IEC 60255-21-2, Class 1;
IEC 60068-2-27
Seismic Vibration
IEC 60255-21-3, Class 2;
IEC 60068-3-3
SIPROTEC 4, 7RW80, Manual
C53000-G1140-C233-4, Edition 07.2018
10 V; 150 kHz to 80 MHz; 80 % AM; 1 kHz;
27 Mhz and 68 MHz spot freq. Dwell time
> 10 sec.
30 A/m continuous; 300 A/m and 1000
V/m for 3 s;
20 V/m; 80 MHz to 1 GHz; 80 % AM; 1 kHz
35 V/m pulsed, 50% duty cycle 1 Hz rep.
rate
Common mode Zone A and B: 300 Veff
(220 Ω, 0.47 µF)
Differential Mode Zone B: 100 Veff (100 Ω,
0.047 µF)
testet with 3.9 KΩ termination resistor
15 % of nominal auxiliary voltage
Shut-down ramp: 60 s
Power off: 5 min.
Start-up ramp: 60 s
EN 61000-6-4 /01.07 + A1
EN 55011 /11.2009 + A1 class A
150 kHz to 30 MHz Limit Class A
30 MHz bis 1000 MHz Limit Class A
1 GHz to 6 GHz Limit Class A
Device is to be assigned Class D (applies only to devices
with > 50 VA power consumption)
Tolerate Voltage interruptions < 60 ms for the nominal
auxiliary voltage.
IEC 60255-21 and IEC 60068
Sinusoidal
10 Hz to 60 Hz: ±0,075 mm amplitude; 60 Hz bis
150 Hz: 1g acceleration
frequency sweep rate 1 octave/min 20 cycles in 3
orthogonal axes.
Semi-sinusoidal
acceleration, duration 11 ms, each 3 shocks in both
directions of the 3 axes
Sinusoidal
1 Hz to 8 Hz: ±7,5 mm amplitude (horizontal axis)
1 Hz to 8 Hz: ±3,5 mm amplitude (vertical axis)
8 Hz to 35 Hz: 2 g acceleration (horizontal axis)
8 Hz to 35 Hz: 1 g acceleration (vertical axis)
Frequency sweep 1 octave/min
1 cycle in 3 orthogonal axes
Technical Data
4.1 General Device Data
165
Advertisement
Table of Contents
