Directed DS4 Plus Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Car Alarm
  5. DS4+
  6. Installation manual

Directed DS4 Plus Installation Manual

Hide thumbs Also See for DS4 Plus:
Table of Contents

Advertisement

Quick Links

INSTALLATION GUIDE
VW10
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-11-02
DS4+

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS4 Plus and is the answer not in the manual?

Questions and answers

Related Manuals for Directed DS4 Plus

Summary of Contents for Directed DS4 Plus

  • Page 1 VW10 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main harness (H1), 12-pin black connector .................. 6 Relay harness (H2), 10-pin white connector .................. 6 Data harness (H3), 8-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Diodes and brake connection only required on vehicles where brake needs to be depressed to start. Additional parts required (maximum required): Resistor 100Ω Fuse 7.5A Diode 6A 2 x 1A Diodes 0 x Resistor 2 x Fuse 2 x Relay DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Lock/Unlock Output H3/7 Orange/Black ISO BUS 2 H3/8 Yellow/Black ISO BUS 1 If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 7: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    Red/White or Red/Blue, pin 8 Headlight switch Slide (black conn. at DS4+ to open light switch) It is important to check that the (+) Parking Lights: Gray/Yellow, pin 3 fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 9 HS CAN High Orange/Black Data OBDII. Violet/Black HS CAN Low Orange/Brown Data OBDII. Violet/Black Red /Yellow VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 10 Steering column module behind steering column trim. Black HS CAN High Orange/Black Data OBDII. Violet/Black HS CAN Low Orange/Brown Data OBDII. Violet/Black Red/Violet VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 11: Type 2

    (-) Ground: Black: 10 Red/White, pin 8 Headlight switch Slide (black conn. at DS4+ to open light switch) (+) Parking Lights: White/Black, pin 1 It is important to check that the fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 12 HS CAN High Orange/Black Data OBDII. Violet/Black HS CAN Low Orange/Brown Data OBDII. Violet/Black Red/White or Red/Yellow VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 13 HS CAN High Orange/Black Data OBDII. Violet/Black HS CAN Low Orange/Brown Data OBDII. Violet/Black Red/White or Red /Yellow VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 14: Type 3

    Ignition Switch It is important to check that the Parking Light Switch fuses are positioned correctly. (black conn. at (black conn. at light switch) ignition switch) (+) Accessory: Black/Red, pin 3 DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 15 VESCM connector A, under drivers dash. Black Brake Black/Red VESCM connector A, under drivers dash. Black Doorlocks [4] Blue/Red VESCM connector A, under drivers dash. Black Trunk Release [4] Violet VESCM connector A, under drivers dash. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 16: Type 4

    (-) Ground: Black: 10 [5] Diode 1A (+) Brake: Black/Red, pin 17 41 24 Slide DS4+ Brown VESCM connector C to open It is important to check that the fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 17 Steering column module behind steering column trim. Black Red/Violet VESCM, connector C, under drivers dash. Brown Brake Black/Yellow VESCM, connector C, under drivers dash. Brown Parking Lights Gray/Yellow VESCM, connector A, under drivers dash. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 18: Type 5

    (+) Brake: Black/Red, pin 17 Key Wrap: Lt. Green/White: 9 41 24 Brown VESCM connector C (-) Ground: Black: 10 Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 19 Steering column module behind steering column trim. Black Red/Yellow VESCM connector C, under drivers dash. Brown Hazards Brown/Red VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 20: Type 6

    (black conn. at light switch) It is important to check that the (+) Parking Lights: Gray/Yellow fuses are positioned correctly. or Gray/Green, pin 3 VESCM - Driver side under dashboard DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 21 FT CAN High Orange/Green Data VESCM connector C, under drivers dash. Brown FT CAN Low Orange/Brown Data VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 22: Type 7

    Parking Lights Interrupt: Red/White, pin 8 Slide Headlight switch DS4+ to open (black conn. at light switch) It is important to check that the (+) Parking Lights: White/Black, pin 1 fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 23 Data Steering column module. Black FT CAN Low Orange/Brown Data Steering column module. Black Red /Yellow VESCM connector C, under drivers dash. Brown Brake Black/Red VESCM connector C, under drivers dash. Brown DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 24: Type 8

    Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 (-) Ground: Black: 10 (+)12V: Pin 1 Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 25 Orange/Brown Data VESCM connector G, under drivers dash. Black Hazards Brown/Red VESCM connector G, under drivers dash. Black HS CAN High Orange/Black Data OBDII. Black HS CAN Low Orange/Brown Data OBDII. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 26: Type 9

    Parking Lights Interrupt: Red/White, pin 8 (+)12V: Pin 1 Slide Headlight switch DS4+ to open (black conn. at light switch) It is important to check that the fuses are positioned correctly. (+) Parking Lights: Gray/Yellow, pin 3 DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 27 VESCM connector G, under drivers dash. Black FT CAN Low Orange/Brown Data VESCM connector G, under drivers dash. Black HS CAN High Orange/Black Data OBDII. Black HS CAN Low Orange/Brown Data OBDII. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 28 VESCM connector G, under drivers dash. Black FT CAN Low Orange/Brown Data VESCM connector G, under drivers dash. Black HS CAN High Orange/Black Data OBDII. Black HS CAN Low Orange/Brown Data OBDII. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 29 Red/White or Red/Black, pin 8 Fuse 5A Slide DS4+ to open Headlight Switch (black conn. at light switch) It is important to check that the fuses are positioned correctly. (+) Parking Lights: Gray/Yellow, pin 3 DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 30 Keyport switch. Black 12V Interrupt Green/Red Keyport switch. Black Brake Black/Red VESCM connector E, under drivers dash. Black HS CAN High Orange/Black Data OBDII. Black HS CAN Low Orange/Brown Data OBDII. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 31: Type 11

    (black conn. at light switch) (black conn. at ignition switch) It is important to check that the (+) Accessory: Black/Red, pin 3 fuses are positioned correctly. (+) Parking Lights: White/Black, pin 1 DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 32 VESCM connector A, under drivers dash. Black Brake Black/Red VESCM connector A, under drivers dash. Black Doorlocks Blue/Red VESCM connector A, under drivers dash. Black Trunk Release Violet VESCM connector A, under drivers dash. Black DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 33: Immobilizer Interface

    N/A: Brown , pin 6 Immobilizer Receiver IMPORTANT!: Not all OEM remotes can be inserted in 556U because of their size. Make sure the key will fit, otherwise it is recommended to use a different method. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 34: Method 3: Immobilizer Interface With Oem Immobilizer Receiver

    - Make connections to the OEM Immobilizer receiver as shown above. - Test and secure mounted loops before reassembling the vehicle. * When possible use valet key for key wrap, if blade key is used, battery must be removed. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 35: Connecting The Module

    Your Combo Sensor is preset for the majority of applications, however it can be adjusted using the DirectLink application, as well as a compatible LED or LCD remote. Please refer to the instructions included with your sensor for more information on how to make adjustments. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 36: When Used In Conjunction With Smartstart

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 37: Module Programming

    By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 41. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 38: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ VW10 © 2017-11-02 Directed. All rights reserved.
  • Page 39 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 40: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 41: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ VW10 © 2017-11-02 Directed. All rights reserved.

  • Page 42: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 43: Quick Reference Guide

    • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 If applicable, you can also start the engine remotely by pressing the Lock button 3 Press Remote vehicle is now in Pit Stop Mode.
  • Page 44 SmartStart compatible This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start.

Table of Contents

Save PDF