Directed DS3+ Installation Manual
2017 audi q5
Hide thumbs
Also See for DS3+:
- Installation manual (35 pages) ,
- Installation manual (28 pages) ,
- Installation manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Directed DS3+
Summary of Contents for Directed DS3+
- Page 1 933.AUDI02 DS3+ / DS4+ v3.16.195.3 2017 Audi Q5...
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram - Key Release Type 1 Wiring diagram - Key Release Type 2 Locating components in the vehicle Immobilizer interface Vehicle connections Module programming Smart Key vehicles without Push-to-Start Pairing remotes Connecting the module 8556T Temperature Sensor... -
Page 3: Introduction
Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information. -
Page 4: Vehicle Function Compatibilities
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Parking lights via hazard control Remote Start Takeover Arm Factory Security SmartStart Disarm Factory Security... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements Keys T-Harness Keys required T-Harness is not compatible. required for for operation compatible... -
Page 6: Installation
Wiring diagram - Key Release Type 1 Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Twisted pair Ignition Switch (in driver’s kick panel, door harness) (16-pin, black connector) FT CAN Low: Orange/Brown (-) Keysense: (-) Starter 2:... - Page 7 Wiring diagram - Key Release Type 2 Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Ignition Switch Twisted pair (16-pin, black connector) (in driver’s kick panel, door harness) HS CAN High: Orange/ Red, pin 6 FT CAN Low: Orange/Brown (-) Keysense:...
-
Page 8: Locating Components In The Vehicle
Locating components in the vehicle UNDERHOOD ECM Engine Control Module (left side of the Engine Compartment) module can also be used for The wiper plastic cover needs to be removed this installation. and the windshield washer tube. (-) Clutch Activation Output: White: 5 & 11 (+)12V IMPORTANT: Position the... - Page 9 Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A Diode (1N4002+) (+) Ignition (-) Ground When Armed (GWA) Output: Blue/White: 2 Refer to the Vehicle connections section for wire Starter (connector side) and connector details.
-
Page 10: Immobilizer Interface
Immobilizer Interface For vehicles with Keyless Entry you must remove battery from OEM key (your OEM remote may differ from the models shown in the illustrations). OEM Receiver Locations A. Instrument panel, driver’s side B. Frame for Multimedia Control Head C. - Page 11 Method 2: Immobilizer interface using 556UXL 556UXL is sold SEPARATELY. Note: The discontinued 556U or 556UW can Move 556UXL loop as close to the front of ignition cylinder (OEM still be used for the installation. Immobilizer Immobilizer Receiver) as possible. Receiver Test and secure mounted loop before reassembling the vehicle.
-
Page 12: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2017 Audi Q5. Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection... - Page 13 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/19 Blue (-) Trunk Input No Connection H2/20 Green (-) Door Input No Connection H2/21 Gray Mandatory (-) Hood Input H2/22 Violet/White (AC) Tach Input No Connection Main harness, 12-pin black connector (H3) Module Connects To Conn./Pin...
- Page 14 RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4...
-
Page 15: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Smart Key vehicles without Push-to-Start Ensure vehicle is in a safe location, and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. -
Page 16: Pairing Remotes
When used in conjunction with Directed SmartStart ® To enable D2D communication between the DS3+/DS4+ and the Directed SmartStart one of the following actions must be performed ® before providing power to the Directed SmartStart unit: ®... -
Page 17: When Used In Conjunction With Smartstart
DO NOT connect the Directed SmartStart ® 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the D2D connector on the module. Refer to the Directed SmartStart ® documentation for further details. D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port. -
Page 18: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 19: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 20 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 21: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module Programming”. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness. -
Page 22: Tach Learning Procedure (Not Needed With Virtual Tach)
Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required. -
Page 23: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor. -
Page 24: Quick Reference Guide (Customer Copy)
3 possible ways you can send commands to your vehicle, using the: Park (P). • Factory remote. • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & Parking lights The parking lights will flash once to indicate the vehicle is Press... - Page 25 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com.