Directed DS3 Installation Manual
2017 ford edge smart key thfon2 compatible
Hide thumbs
Also See for DS3:
- Installation manual (26 pages) ,
- Installation manual (24 pages) ,
- Installation manual (24 pages)
Related Manuals for Directed DS3
Summary of Contents for Directed DS3
- Page 1 933.FORD12 DS3+ / DS4+ v1.60.195.3 2017 Ford Edge (Smart Key) THFON2 Compatible (Sold Separately)
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram without OEM Remote Start and with T-Harness (THFON2 Rev.2) Wiring diagram without OEM Remote Start and with T-Harness (THFON2 Rev.1) Wiring diagram without OEM Remote Start and without T-Harness Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev.2) Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev.1) Wiring diagram with OEM Remote Start and without T-Harness... -
Page 3: Introduction
Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information. -
Page 4: Vehicle Function Compatibilities
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Parking Lights Control Remote Start Takeover Door Lock Control SmartStart Door Unlock... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements T-Harness Keys required for Keys required THFON2 programming for operation... -
Page 6: Installation
Wiring diagram without OEM Remote Start and with T-Harness (THFON2 Rev. 2) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Gateway Module (on OBDII connector or right of steering column) Type 2 Type 1... -
Page 7: Wiring Diagram Without Oem Remote Start And With T-Harness (Thfon2 Rev.1)
Wiring diagram without OEM Remote Start and with T-Harness (THFON2 Rev. 1) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Gateway Module (on OBDII connector or right of steering column) Type 2 Type 1... -
Page 8: Wiring Diagram Without Oem Remote Start And Without T-Harness
Wiring diagram without OEM Remote Start and without T-Harness Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( (+)12V: Pin 24 CAN 1 High: White/Blue or Blue, pin 20 Gateway Module (on OBDII connector or right of steering column) -
Page 9: Wiring Diagram With Oem Remote Start And With T-Harness (Thfon2 Rev.2)
Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev. 2) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Gateway Module (on OBDII connector or right of steering column) Type 2 Type 1... -
Page 10: Wiring Diagram With Oem Remote Start And With T-Harness (Thfon2 Rev.1)
Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev. 1) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Gateway Module (on OBDII connector or right of steering column) Type 2 Type 1... -
Page 11: Wiring Diagram With Oem Remote Start And Without T-Harness
Wiring diagram with OEM Remote Start and without T-Harness Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( (+)12V: Pin 24 CAN 2 High: Refer to the Gray/Orange or Orange, pin 23 Starter disable connection CAN 2 Low:... -
Page 12: Locating Components In The Vehicle
Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A diode [1N4002+ ] (+) Ignition (-) Ground When Armed (GWA) Output: Blue/White: 2 Refer to the Vehicle connections section for wire and Starter (conn. -
Page 13: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2017 Ford Edge (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color... - Page 14 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/17 Black/White (-) E-Brake Input No Connection H2/18 Orange/Black (+) Instant Alarm Input No Connection H2/19 Blue (+) Instant Alarm Input No Connection H2/20 Green (-) Trunk Input No Connection H2/21 Gray...
- Page 15 RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4...
-
Page 16: Module Programming
For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. DS3+: Connect the 12-pin main power harness to the DS3+ module FIRST. Wait until the LED turns ON solid red before proceeding to the next step. -
Page 17: Module Programming For Security-Only Installations
Connect the 12-pin main power harness to the module. DS3+ DS4+ DS3+: Wait until the LED turns ON solid red then proceed to the next step. Must connect Solid Solid Solid DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. -
Page 18: Pairing Remotes
"QR2" Tech Tip, and on the DS3/DS4 Quick Reference Install guide. Pairing sensors: Sensors should be connected to the DS3/DS4 module prior to connecting the 12-pin main power harness. When powered up, connected peripherals will pair automatically. -
Page 19: When Used In Conjunction With Smartstart
SmartStart with Pigtails – The gray wire must be connected to a ground source. Loops Pigtails DO NOT connect the Directed SmartStart 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the ® D2D connector on the module. Refer to the Directed SmartStart documentation for further details. -
Page 20: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 21: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 22 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 23: Soft Reset
If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness. Press and hold the programming button, then connect the 12-pin harness to the module. DS3+: Wait 3 seconds until the LED turns ON solid orange then release the programming button. & &... -
Page 24: Tach Learning Procedure (Not Needed With Virtual Tach)
Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required. -
Page 25: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor. -
Page 26: Quick Reference Guide (Customer Copy)
Factory remote. Š The alarm system is triggered. 2. Aftermarket remote. Š The doors/hood are open. 3. Directed SmartStart application via your smartphone. Š The transmission is not in Park (P). ® Š The vehicle battery voltage is too low. - Page 27 SmartSchedule, vehicle status, roadside assistance, parked car finder and more. The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.