1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DS4+
  6. Installation manual

Directed DS4+ Installation Manual

Hide thumbs Also See for DS4+:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
INSTALLATION GUIDE
TL8
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-08-23
DS4+

Advertisement

Table of Contents
loading

Related Manuals for Directed DS4+

Summary of Contents for Directed DS4+

  • Page 1 INSTALLATION GUIDE Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 OEM Remote Start Fuse Location ....................5 Physical OEM Remote Start Fuse Location..................5 Vehicle application guide ......................6 Wiring connections ......................... 7 Main harness (H1), 12-pin black connector .................. 7 Relay harness (H2), 10-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    20 seconds. If the vehicle is equipped with an Add-On Lexus/Toyota OEM remote starter: The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot coexist. See locating the OEM Remote Start on page 5.

  • Page 5: Oem Remote Start Fuse Location

    Behind glove box, high in passenger kick panel. Toyota Highlander (Smart Key) Behind glove box, high in passenger kick panel. Toyota Highlander Hybrid Bottom of instrument panel junction box, under drivers dash. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 6: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 7: Wiring Connections

    Violet/Brown No Connection H3/7 Orange/Black No Connection H3/8 Yellow/Black No Connection If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 8: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 9: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    (-) Unlock: Lt. Green, pin 2 Slide DS4+ to open It is important to check that the White Conn. fuses are positioned correctly. (at Main Body ECU) (+) 12V: Blue, pin 13 DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 10 White HS CAN Low Black Data OBDII. White Autolight Pink Main body ECU. White Lock Blue Main body ECU. White Unlock Lt. Green Main body ECU. White Blue Main body ECU. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 11 White HS CAN Low Black Data OBDII. White Autolight Pink Main body ECU. White Lock Blue Main body ECU. White Unlock Lt. Green Main body ECU. White Blue Dash fuse box. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 12 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 13: Type 2

    (-) Lock: Red, pin 29 (-) Unlock: Lt. Green, pin 2 Slide DS4+ to open It is important to check that the fuses are positioned correctly. (+) 12V: Dash Red, pin 6 Fuse Box DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 14 OBDII. White Autolight Green Bottom of dash fuse box. White Lock Bottom of dash fuse box. White Unlock Lt. Green Bottom of dash fuse box. White Bottom of dash fuse box. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 15 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 16: Type 3

    (-) Lock: Pin 29 (-) Unlock: Pin 2 Slide DS4+ to open It is important to check that the fuses are positioned correctly. White Conn. (at Main Body ECU) (+)12V: Green or Black, pin 1 DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 17 HS CAN High Lt.Blue Data OBDII. White HS CAN Low White Data OBDII. White Autolight White Main body ECU. White Lock Lt.Blue Main body ECU. White Unlock Green Main body ECU. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 18 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 19: Type 4

    (-) Lock: Pink, pin 29 (-) Unlock: Violet, pin 2 White conn. Slide DS4+ (at dash fuse box) to open (+) 12V: Blue, pin 1 It is important to check that the fuses are positioned correctly. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 20 Network Gateway ECU behind glovebox. Black HS CAN Low White Data Network Gateway ECU behind glovebox. Black Autolight Green Main body ECU. White Lock Pink Main body ECU. White Unlock Violet Main body ECU. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 21 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 22: Type 5

    (-) Unlock: pin 29 Lt. Blue, pin 2 Slide DS4+ to open It is important to check that the fuses are positioned correctly. White Conn. (at Main Body ECU) (+)12V: Green, pin 1 DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 23 Data Steering sensor on steering column. Blue Lt. Green Steering lock connector. Black Autolight Black Main body ECU. White Lock Violet Main body ECU. White Unlock Lt. Blue Main body ECU. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 24 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 25: Type 6

    (-) Unlock: Lt. Green, pin 2 Slide DS4+ to open It is important to check that the White Conn. fuses are positioned correctly. (at Main Body ECU) (+) 12V: Blue, pin 13 DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 26 HS CAN Low Black Data Main body ECU. White Autolights Pink Main body ECU. White Lock Blue Main body ECU. White Unlock Lt. Green Main body ECU. White Blue Main body ECU. White DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 27 2. Remove white 1. Remove plastic housing metal clip 2. Move the white plastic housing over enough to access the SLP connector. Steering Lock connector Steering Lock connector DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 28: Connecting The Module

    Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) (Violet/White, pin 22) and learned successfully to the DS4+. Note: Refer to www.directechs.com for more information. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 29: Adjusting The 8504D Shock Sensor

    All ports can be configured for D2D 1.0 and 2.0; however, if the device is not configured accordingly as well, it will not be recognized. • All ports need to be configured via the web, but the above is the recommended installation configuration. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 30: Module Programming

    By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 34. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 31: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ TL8 © 2017-08-23 Directed. All rights reserved.
  • Page 32 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 33: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 34: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ TL8 © 2017-08-23 Directed. All rights reserved.

  • Page 35: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 36: Quick Reference Guide

    Refer to your authorized installation center for more specific • Aftermarket remote. information. • Directed SmartStart application via your smartphone. Button(s) Actions If applicable, you can also start the engine remotely by pressing the Lock button 3 Press & hold for 1 second to lock.
  • Page 37 SmartStart compatible Notes This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone;...

Table of Contents