Directed DS3+ Installation Manual
2019 nissan qashqai (smart key). 933.niss06 3.23.195.3
Hide thumbs
Also See for DS3+:
- Installation manual (35 pages) ,
- Installation manual (37 pages) ,
- Installation manual (24 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
DS3+ / DS4+
2019 Nissan Qashqai (Smart Key). 933.NISS06 3.23.195.3
Designed by Installers for Installers
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed DS3+
Summary of Contents for Directed DS3+
- Page 1 2019 Nissan Qashqai (Smart Key). 933.NISS06 3.23.195.3 Designed by Installers for Installers © 2021 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THNIN5) Wiring diagram Locating components in the vehicle Vehicle connections Connecting the module Important! 8556T Temperature Sensor 8504D Combo Sensor RF Systems When used in conjunction with SmartStart D2D port configuration Manual Transmission Module programming... -
Page 3: Introduction
Introduction DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about which configuration is best for your application. Warning! This module can be configured using the web tool located at www.directechs.com. -
Page 4: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness Keys required for Keys required for THNIN5 compatible programming operation... -
Page 5: Installation
Wiring diagram with T-Harness (THNIN5) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( THNIN5 (Optional T-Harness) BCM Connector M19 BCM Connector B16 (green conn. at BCM) (black conn. -
Page 6: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( BCM Connector B16 (green conn. at BCM) HS CAN High: Blue or Lavender/Blue, pin 20 HS CAN Low: Pink or Lavender/Pink,pin 40 (-) Disarm: Pink, pin 13... -
Page 7: Locating Components In The Vehicle
Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. (+) Starter Disable Output: Violet/Black: 8 1A Diode (1N4002+) (-) Ignition: Yellow or (-) Starter: Green Lavender/L.t Green, pin 27 or Blue, pin 19 Legend: Mandatory Connections... -
Page 8: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2019 Nissan Qashqai (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color... - Page 9 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/11 Brown/White No Connection H2/12 Brown/White (-) Ignition Output BCM under driver dash, gray 40 pin plug, pin 27 Lavender/Lt. Green Remote Start Only H2/13 White (+) AUX 1 Output No Connection H2/14 White (+)
- Page 10 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/44 Violet/White (AC) Tach Input No Connection Main harness, 12-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H3/1 Blue/White Relay N.C. No Connection No Connection H3/2 Blue/White...
- Page 11 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H4/3 Red/Black (+) 12 Volt Input (Accessory/Starter) No Connection H4/4 Red/Black (+) 12 Volt Input No Connection H4/5 Pink/Black Flex Relay (pin 87a) No Connection H4/6 Pink/Black Relay N.C. – No Connection No Connection H4/7 Pink/White...
- Page 12 Temperature sensor harness, 2-pin black connector (H7) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H7/1 Black Temperature Sensor H7/2 Black Temperature Sensor Mandatory H7/3 Black Temperature Sensor Mandatory H7/4 Black Temperature Sensor 933.NISS06 3.23.195.3 2019 Nissan Qashqai (Smart Key) ©2021 VOXX•DEI LLC.
-
Page 13: Connecting The Module
Configuring the system DS3+ Flashing the module using your computer: 1. Disconnect the main module from any (+) 12V power source, then connect it to your computer using the XKLoader2. 2. Go to www.directechs.com using Internet Explorer; the configuration wizard will be displayed automatically. Follow the instructions in the pop-up window that will be displayed when the module is detected. -
Page 14: Rf Systems
RF Systems An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. -
Page 15: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission, remote starts on any convertible vehicle or a vehicle with a removable top, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata etc... This system supports manual transmission installations. -
Page 16: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. (For security-only programming, see next section.) Please ensure that the vehicle is in a safe location, and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. -
Page 17: Module Programming For Security-Only Installations
Module programming for security-only installations Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes. To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. -
Page 18: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. - Page 19 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 20: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module Programming”. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin 12-pin harness main power harness. -
Page 21: Learning The Tach (Not Needed With Virtual Tach)
Learning the Tach (not needed with Virtual Tach) Tach comes preprogrammed, therefore learning is not required; however, it can be readjusted with the following operations: 1. Start the vehicle using the key. 2. Within 5 seconds, press and hold the Control Center (antenna), the LED/Valet Pod (standalone switch) or the main module programming button until the LED turns ON solid. -
Page 22: Limited Lifetime Consumer Warranty
Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;... -
Page 23: Quick Reference Guide
Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode. - Page 24 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.