Download Print this page

HP 5500 EI series Configuration Manual: Configuring Ospfv3 Route Redistribution

Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424

Advertisement

Configuring OSPFv3 route redistribution

Because OSPFv3 is a link state routing protocol, it cannot directly filter LSAs to be advertised. OSPFv3
filters only redistributed routes. Only routes that are not filtered out can be advertised in LSAs.
Executing the import-route or default-route-advertise command on a router makes it become an ASBR.
To configure OSPFv3 route redistribution:
Step
1.
Enter system view.
2.
Enter OSPFv3 view.
(Optional.) Specify a default
3.
cost for redistributed routes.
4.
Configure OSPFv3 to
redistribute routes from other
routing protocols.
5.
(Optional.) Configure
OSPFv3 to redistribute a
default route.
6.
(Optional.) Configure
OSPFv3 to filter redistributed
routes.
Tuning and optimizing OSPFv3 networks
This section describes configurations of OSPFv3 timers, interface DR priority, and the logging of
neighbor state changes.
Configuration prerequisites
Before you tune and optimize OSPFv3 networks, complete the following tasks:
Configure IPv6 addresses for interfaces to ensure IPv6 connectivity between neighboring nodes.
Enable OSPFv3.
Command
system-view
ospfv3 [ process-id | vpn-instance
vpn-instance-name ] *
default cost value
import-route protocol [ process-id |
all-processes | allow-ibgp ] [ cost cost |
route-policy route-policy-name | type
type ] *
default-route-advertise [ [ always |
permit-calculate-other ] | cost cost |
route-policy route-policy-name | type
type ] *
filter-policy { acl6-number | prefix-list
prefix-list-name } export [ protocol
[ process-id ] ]
346
Remarks
N/A
N/A
The default setting is 1.
By default, route redistribution
is disabled.
By default, no default route is
redistributed.
This command can only inject
and advertise a default route.
By default, OSPFv3 accepts
all redistributed routes.
This command filters only
routes redistributed with the
import-route command. If the
import-route command is not
configured, executing this
command does not take
effect.

Advertisement

Troubleshooting

This manual also for:

5500 si series

Comments to this Manuals

Symbols: 0
Latest comments: