Omron E5CN-HT Communications Manual page 99

Address
Parameter name
Four-byte Two-byte
mode mode
0500 2500 Operation/Adjustment Protect
0502 2501 Initial Setting/Communications
Protect
0504 2502 Setting Change Protect
0506 2503 PF Key Protect
0508 2504 Move to Protect Level
050A 2505 Password to Move to Protect
Level
050C 2506 Parameter Mask Enable
0600 2600 Manual MV
0604 2602 Remote SP Monitor
0608 2604 Heater Current 1 Value Monitor
060A 2605 MV Monitor (Heating)
060C 2606 MV Monitor (Cooling)
060E 2607 Valve Opening Monitor
0610 2608 Program No.
0612 2609 Segment No. Monitor
0614 260A Remaining Standby Time Moni-
tor
0616 260B Elapsed Program Time Monitor
0618 260C Remaining Program Time Moni-
tor
061A 260D Elapsed Segment Time Monitor
061C 260E Remaining Segment Time Moni-
tor
061E 260F Program Repetitions Monitor
0620 2610 SP Mode Setting Monitor
5.1 Variable Area (Setting Range) List
Setting (monitor) value
H'00000000(0) to H'00000005(5)
0: No control
1: Run level (PV allowed, PV/SP allowed, others allowed), program level
allowed, adjustment level allowed, PID setting level prohibited
2: Run level (PV allowed, PV/SP allowed, others allowed), program level
allowed, adjustment level prohibited, PID setting level prohibited
3: Run level (PV allowed, PV/SP allowed, others allowed), program level pro-
hibited, adjustment level prohibited, PID setting level prohibited
4: Run level (PV allowed, PV/SP allowed, others prohibited), program level
prohibited, adjustment level prohibited, PID setting level prohib-
ited
5: Run level (PV allowed, PV/SP prohibited, others prohibited), program level
prohibited, adjustment level prohibited, PID setting level prohib-
ited
H'00000000 (0): Move to initial setting/communications setting level is allowed.
(Move to advanced function setting level is displayed.)
H'00000001 (1): Move to initial setting/communications setting level is allowed.
(Move to advanced function setting level is not displayed.)
H'00000002 (2): Move to initial setting/communications setting level is prohib-
ited.
H'00000000 (0): OFF (Changing of setup on controller display is allowed.)
H'00000001 (1): ON (Changing of setup on controller display is prohibited.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position proportional (Closed and direct setting of position proportional MV
ON): H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
SP Lower Limit to SP Upper Limit
H'00000000 to H'00000226 (0.0 to 55.0)
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating and cooling: H'00000000 to H'0000041A (0.0 to 105.0)
H'00000000 to H'0000041A (0.0 to 105.0)
H'FFFFFF9C to H'0000044C (−10.0 to 110.0)
H'00000000 to Hí00000007 (0 to 7)
H'00000000 to Hí0000001F (0 to 31)
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 (0): Program SP mode
H'00000001 (1): Remote SP mode
H'00000002 (2): Fixed SP mode
Level
Protect
Manual
Control
Operation
None
Operation
None
5-3