Omron E5CN-HT Communications Manual page 54

SECTION 3 Communications Data for CompoWay/F
Variable
Address Parameter name
type
C1 (81) 0022 MV at Reset
C1 (81) 0023 MV at PV Error
C1 (81) 0024 Manual MV
C1 (81) 0026 MV Upper Limit (See note 1.)
C1 (81) 0027 MV Lower Limit (See note 1.)
C1 (81) 0028 Move to Protect Level
C1 (81) 0029 Password to Move to Protect Level
C1 (81) 002A Parameter Mask Enable
C1 (81) 002B PF Key Protect
C1 (81) 002C MV Change Rate Limit
C1 (81) 002D Position Proportional Dead Band
C1 (81) 002E Open/Close Hysteresis
C1 (81) 002F Heater Overcurrent Detection 1
C1 (81) 0030 Heater Overcurrent Detection 2
C1 (81) 0031 Extraction of Square Root Low-cut
Point
C1 (81) 0032 Program No.
C1 (81) 0033 Fixed SP
C1 (81) 0034 Standby Time
C1 (81) 0035 Program SP Shift Value
C1 (81) 0036 RSP 0 before Correction
C1 (81) 0037 RSP 1 before Correction
C1 (81) 0038 RSP 2 before Correction
C1 (81) 0039 RSP 3 before Correction
C1 (81) 003A RSP 4 before Correction
C1 (81) 003B RSP 5 before Correction
C1 (81) 003C RSP 6 before Correction
C1 (81) 003D RSP 7 before Correction
C1 (81) 003E RSP 8 before Correction
C1 (81) 003F RSP 9 before Correction
C1 (81) 0040 RSP 10 before Correction
3-4
Setting (monitor) value
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 (−1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 (−1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position proportional (Floating or direct setting of position proportional
MV OFF): H'FFFFFFFF to H'00000001 (−1 to 1)
Position proportional (Closed and direct setting of position proportional
MV ON): H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Standard: MV lower limit + 0.1 to H'0000041A
(MV lower limit + 0.1 to 105.0)
Heating/cooling: H'00000000 to H'0000041A (0.0 to 105.0)
Position proportional (closed): MV lower limit +0.1 to H'0000041A
(MV lower limit +0.1 to 105.0)
Standard: H'FFFFFFCE to MV upper limit −0.1
(−5.0 to MV upper limit −0.1)
Heating/cooling: H'FFFFFBE6 to H'00000000 (−105.0 to 0.0)
Position proportional (closed): H'FFFFFFCE to MV upper limit −0.1
(−5.0 to MV upper limit −0.1)
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 to H'000003E8 (0.0 to 100.0)
H'00000001 to H'00000064 (0.1 to 10.0)
H'00000001 to H'000000C8 (0.1 to 20.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000003E8 (0.0 to 100.0)
H'00000000 to Hí00000007 (0 to 7)
SP lower limit to SP upper limit
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Level
Adjustment
Manual
Control
Adjustment
Protect
Adjustment
Operation
Adjustment