Omron E5CN-HT Communications Manual page 65

Variable
Address Parameter name
type
C4 (84) 0000 Program Selection
C4 (84) 0001 No. of Segments Used (See note 1.)
C4 (84) 0002 Segment Selection (See note 1.)
C4 (84) 0003 Segment Type (See note 2.)
C4 (84) 0004 Segment SP (See note 2.)
C4 (84) 0005 Segment Slope (See note 2.)
C4 (84) 0006 Segment Time (See note 2.)
C4 (84) 0007 PID Set No. (See note 1.)
C4 (84) 0008 Alarm Value 1
C4 (84) 0009 Alarm Upper Limit 1 (See note 1.)
C4 (84) 000A Alarm Lower Limit 1 (See note 1.)
C4 (84) 000B Alarm Value 2 (See note 1.)
C4 (84) 000C Alarm Upper Limit 2 (See note 1.)
C4 (84) 000D Alarm Lower Limit 2 (See note 1.)
C4 (84) 000E Alarm Value 3 (See note 1.)
C4 (84) 000F Alarm Upper Limit 3 (See note 1.)
C4 (84) 0010 Alarm Lower Limit 3 (See note 1.)
C4 (84) 0011 Program Repetitions (See note 1.)
C4 (84) 0012 Program Link Destination No. (See note
1.)
C4 (84) 0013 Time Signal 1 Set Segment (See note
1.)
C4 (84) 0014 Time Signal 1 ON Time (See note 1.)
C4 (84) 0015 Time Signal 1 OFF Time (See note 1.)
C4 (84) 0016 Time Signal 2 Set Segment (See note
1.)
C4 (84) 0017 Time Signal 2 ON Time (See note 1.)
C4 (84) 0018 Time Signal 2 OFF Time (See note 1.)
Note 1: The set values for the program specified in the Program Selection parameter are accessed for the following parameters:
No. of Segments Used, Segment Selection, PID Set No., Alarm Values 1 to 3, Alarm Upper Limits 1 to 3, Alarm Lower
Limits 1 to 3, Program Repetitions, Program Link Destination No., Time Signal 1 and 2 Set Segments, Time Signal 1 and 2
ON Times, and Time Signal 1 and 2 OFF Times. Check the set value of the Program Selection parameter before
accessing these parameters.
Note 2: The set values for the program specified in the Program Selection parameter and the section specified in the Segment
Selection parameter are accessed for the following parameters: Segment Type, Segment SP, Segment Slope, and
Segment Time. Check the set values of the Program Selection parameter and the Segment Selection parameter before
accessing these parameters.
3.1 Variable Area (Setting Range) List
Setting (monitor) value
H'00000000 to H'00000007 (0 to 7)
H'00000001 to H'00000020 (32)
H'00000000 to H'0000001F (31)
H'00000000 (0): Ramp
H'00000001 (1): Soak
H'00000002 (2): Step
SP lower limit to SP upper limit
H'00000000 to H'00007E90 (0 to 32400)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00000008 (0 to 8) (0): Automatic Selection
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
'00000000 to '0000270F (0 to 9999)
H'FFFFFFFF(−1): No link
H'00000000 to H'00000007 (0 to 7)
H'00000000 (0) to No. of segments used −1
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 (0) to No. of segments used −1
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
Level
Program
setting
3-15