Omron E5CN-HT Communications Manual page 64

SECTION 3 Communications Data for CompoWay/F
Variable
Address Parameter name
type
C3 (83) 0073 PV/SP Display Screen Selection
C3 (83) 0074 MV Display Selection
C3 (83) 0075 PV Decimal Point Display
C3 (83) 0076 PV Status Display Function
C3 (83) 0077 SV Status Display Function
C3 (83) 0078 Control Output 1 ON/OFF Count Alarm
Set Value
C3 (83) 0079 Control Output 2 ON/OFF Count Alarm
Set Value
C3 (83) 0083 Display Refresh Period
C3 (83) 0084 Program Time Unit
C3 (83) 0085 Time Setting/Gradient Setting
C3 (83) 0086 Gradient Time Setting Unit
C3 (83) 0087 Reset Operation
C3 (83) 0088 Startup Operation
C3 (83) 0089 Operation End Operation
C3 (83) 008A PV Start
C3 (83) 008B Program End ON Time
C3 (83) 008C Standby Time Unit
C3 (83) 008D Program SP Shift Value Addition
C3 (83) 008E RSP Broken-line Correction Display
Addition
Note 1: Selection is not possible when ON/OFF control is set.
Note 2: Selection is not possible if the Reset Operation parameter is set to fixed SP operation.
3-14
Setting (monitor) value
H'00000000 (0): Only PV/SP displayed (no No. 3 display).
H'00000001 (1): The PV/SP/Program No. or Segment No., and the
PV/SP/MV are displayed in order.
H'00000002 (2): The PV/SP/MV and PV/SP/Program No. or Segment
No. are displayed in order.
H'00000003 (3): Only the PV/SP/Program No. or Segment No. are
displayed.
H'00000004 (4): Only the PV/SP/MV are displayed.
H'00000005 (5): The PV/SP/Program No. or Segment No., and the
PV/SP/Remaining Segment Time are displayed in
order.
H'00000006 (6): The PV/SP/MV and PV/SP/Remaining Segment
Time are displayed in order.
H'00000007 (7): Only the PV/SP/Remaining Segment Time are dis-
played.
H'00000000 (0): MV (heating)
H'00000001 (1): MV (cooling)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): Manual
H'00000002 (2): Reset
H'00000003 (3): Alarm 1
H'00000004 (4): Alarm 2
H'00000005 (5): Alarm 3
H'00000006 (6): Alarm 1 to 3 OR status
H'00000007 (7): Heater alarm
H'00000008 (8): Standby
H'00000000 to H'00000008 (0 to 8)
* Same as for PV Status Display Function
H'00000000 to H'0000270F (0 to 9999)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 (0): OFF
H'00000001 (1): 0.25
H'00000002 (2): 0.5
H'00000003 (3): 1.0
H'00000000 (0): Hours, minutes
H'00000001 (1): Minutes, seconds
H'00000000 (0): Time setting
H'00000001 (1): Gradient setting
H'00000000 (0): Minutes
H'00000001 (1): Hours
H'00000000 (0): Stop control
H'00000001 (1): Fixed SP operation
H'00000000 (0): Continue control at final SP
H'00000001 (1): Reset
H'00000002 (2): Run
H'00000003 (3): Manual (See note 1.)
H'00000000 (0): Reset
H'00000001 (1): Continue control at final SP
H'00000002 (2): Fixed SP mode (See note 2.)
H'00000000 (0): SP-priority SP start
H'00000001 (1): Slope-priority PV start
H'00000000 to H'00000064 (0.0 to 10.0)
H'FFFFFFFF(ON)
H'00000000 (0): Hours, minutes
H'00000001 (1): Days, hours
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
Level
Advanced
function
setting
Advanced
function
setting
Initial
setting
Advanced
function
setting