Omron E5CN-HT Communications Manual page 102

SECTION 5 Communications Data for Modbus
Address
Four- Two- Parameter name
byte byte
mode mode
1802 3801 No. of Segments Used (See note 1.)
1804 3802 Segment Selection (See note 1.)
1806 3803 Segment Type (See note 2.)
1808 3804 Segment SP (See note 2.)
180A 3805 Segment Slope (See note 2.)
180C 3806 Segment Time (See note 2.)
180E 3807 PID Set No. (See note 1.)
1810 3808 Alarm Value 1 (See note 1.)
1812 3809 Alarm Value Upper Limit 1 (See note 1.)
1814 380A Alarm Value Lower Limit 1 (See note 1.)
1816 380B Alarm Value 2 (See note 1.)
1818 380C Alarm Value Upper Limit 2 (See note 1.)
181A 380D Alarm Value Lower Limit 2 (See note 1.)
181C 380E Alarm Value 3 (See note 1.)
181E 380F Alarm Value Upper Limit 3 (See note 1.)
1820 3810 Alarm Value Lower Limit 3 (See note 1.)
1822 3811 Program Repetitions (See note 1.)
1824 3812 Program Link Destination No. (See note 1.)
1826 3813 Time Signal 1 Set Segment (See note 1.)
1828 3814 Time Signal 1 ON Time (See note 1.)
182A 3815 Time Signal 1 OFF Time (See note 1.)
182C 3816 Time Signal 2 Set Segment (See note 1.)
182E 3817 Time Signal 2 ON Time (See note 1.)
1830 3818 Time Signal 2 OFF Time (See note 1.)
0A00 2A00 Proportional Band (See note 3.)
0A02 2A01 Integral Time (See note 3.)
0A04 2A02 Derivative Time (See note 3.)
0A0A 2A05 MV Upper Limit (See note 3.)
Note: The alarm function can also be used in Controllers without alarm output terminals. In this case, confirm alarm occurrences via the
status data.
Note 1: The set values for the program specified in the Program Selection parameter are accessed for the following parameters: No. of
Segments Used, Segment Selection, PID Set No., Alarm Values 1 to 3, Alarm Upper Limits 1 to 3, Alarm Lower Limits 1 to 3, Program
Repetitions, Program Link Destination No., Time Signal 1 and 2 Set Segments, Time Signal 1 and 2 ON Times, and Time Signal 1 and
2 OFF Times. Check the set value of the Program Selection parameter before accessing these parameters.
Note 2: The set values for the program specified in the Program Selection parameter and the section specified in the Segment Selection
parameter are accessed for the following parameters: Segment Type, Segment SP, Segment Slope, and Segment Time. Check the set
values of the Program Selection parameter and the Segment Selection parameter before accessing these parameters.
Note 3: The parameter for the currently selected PID set will be accessed. For setup area 1, however, the currently selected PID set is fixed at
PID1.
5-6
Setting (monitor) value
H'00000001 to H'00000020 (32)
H'00000000 to H'0000001F (31)
H'00000000 (0): Ramp
H'00000001 (1): Soak
H'00000002 (2): Step
SP lower limit to SP upper limit
H'00000000 to H'00007E90 (0 to 32400)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00000008 (0 to 8) (0): Automatic Selection
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
'00000000 to '0000270F (0 to 9999)
H'FFFFFFFF(−1): No link
H'00000000 to H'00000007 (0 to 7)
H'00000000 (0) to No. of segments used −1
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 (0) to No. of segments used −1
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
H'00000000 to H'00009959 (0.00 to 99.59) (hours, minutes)
H'00000000 to H'00009959 (0.00 to 99.59) (minutes, seconds)
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
Standard, heating/cooling, position proportional (closed):
H'00000000 to H'00007E90 (0.0 to 3240.0)
Position proportional (floating): H'00000001 to H'00007E90
(0.1 to 3240.0)
H'00000000 to H'00007E90 (0.0 to 3240.0)
Standard: MV lower limit +0.1 to H'0000041A
(MV lower limit +0.1 to 105.0)
Heating/cooling: H'00000000 to H'0000041A (0.0 to 105.0)
Position proportional (closed): MV lower limit +0.1 to H'0000041A)
MV lower limit +0.1 to 105.0)
Level
Program
Adjustment