Omron E5CN-HT Communications Manual page 109

Address
Parameter name
Four-byte Two-byte
mode mode
1206 3203 Monitor/Setting Item 2
1208 3204 Monitor/Setting Item 3
120A 3205 Monitor/Setting Item 4
120C 3206 Monitor/Setting Item 5
1300 3300 Startup Operation
1302 3301 SP Tracking
1304 3302 PID Set Automatic Selection
Data
1306 3303 PID Set Automatic Selection
Hysteresis
1308 3304 PV Dead Band
130A 3305 Cold Junction Compensation
Method
α
1314 330A
131E 330F AT Calculated Gain
1320 3310 AT Hysteresis
1322 3311 Limit Cycle MV Amplitude
1328 3314 Heater Burnout Latch
132A 3315 Heater Burnout Hysteresis
132C 3316 HS Alarm Latch
132E 3317 HS Alarm Hysteresis
1334 331A Operation End Operation
1338 331C HB ON/OFF
133A 331D Program End ON Time (See
note 1.)
133C 331E Input Error Output
133E 331F Input Shift Type
1340 3320 MV at Reset and Error Addition
1344 3322 RT
1346 3323 HS Alarm Use
Note 1: Selection is not possible when ON/OFF control is being used.
5.1 Variable Area (Setting Range) List
Setting (monitor) value
H'00000000 to H'00000015 (0 to 21)
* Same as for Monitor/Setting Item 1.
H'00000000 to H'00000015 (0 to 21)
* Same as for Monitor/Setting Item 1.
H'00000000 to H'00000015 (0 to 21)
* Same as for Monitor/Setting Item 1.
H'00000000 to H'00000015 (0 to 21)
* Same as for Monitor/Setting Item 1.
H'00000000 (0): Continue control at final SP
H'00000001 (1): Reset
H'00000002 (2): Run
H'00000003 (3): Manual (See note 1.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): PV
H'00000001 (1): DV
H'00000002 (2): SP
H'0000000A to H'0000270F (0.10 to 99.99)
H'00000000 to H'00007E90 (0 to 32400)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 to H'00000064 (0.00 to 1.00)
H'00000001 to H'00000064 (0.1 to 10.0)
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'000003E7 (0.01 to 9.99)
H'00000032 to H'000001F4 (5.0 to 50.0)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'000001F4 (0.1 to 50.0)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'000001F4 (0.1 to 50.0)
H'00000000 (0): Reset
H'00000001 (1): Continue control at final SP
H'00000002 (2): Fixed SP mode
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 to H'00000064 (0.0 to 10.0)
H'FFFFFFFF(−1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): Temperature input 1-point shift
H'00000001 (1): Temperature input 2-point shift
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
Level
Advanced
function
setting
Initial
setting
Advanced
function
setting
5-13