Danfoss FC 300 Design Manual page 64

4. FC 300 Selection
Line Supply 3 x 380-500 V AC (FC 302), 3 x 380-480 V AC (FC 301)
FC 301/FC 302
Typical Shaft Output [kW]
Enclosure
20/IP 21
Enclosure
20 (FC 301 on-
ly)
Enclosure
55, 66
4
Output current
High overload 160% for 1 minute
Max. input current
0.33-10 hp [0.37-7.5 kW] only available as 160% high overload.
64
PK 37 PK 55
0.37 0.55 0.75
IP
A2
IP
A1
IP
A5
Shaft output [kW] 0.37 0.55 0.75
Continuous
1.3 1.8
(3 x 380-440 V) [A]
Intermittent
2.1 2.9
(3 x 380-440 V) [A]
Continuous
1.2 1.6
(3 x 440-500 V) [A]
Intermittent
1.9 2.6
(3 x 440-500 V) [A]
Continuous KVA
0.9 1.3
(400 V AC) [KVA]
Continuous KVA
0.9 1.3
(460 V AC) [KVA]
Max. cable size
(line, motor, brake)
0.00031-0.0062 in. [0.2-4 mm]
[AWG] 2) [mm 2 ]
Continuous
1.2 1.6
(3 x 380-440 V) [A]
Intermittent
1.9 2.6
(3 x 380-440 V) [A]
Continuous
1.0 1.4
(3 x 440-500 V) [A]
Intermittent
1.6 2.2
(3 x 440-500 V) [A]
1) 10
Max. pre-fuses [A]
Environment
Estimated power
loss
35
at rated max. load
[W] 4)
Weight,
4.7 4.7
enclosureIP 20
Enclosure IP 55, 66 13.5 13.5 13.5 13.5
Efficiency 4) 0.93 0.95 0.96 0.96
MG.33.B9.22 - VLT
PK7
P1K1 P1K5 P2K2 P3K0 P4K0 P5K5 P7K5
5
1.1 1.5 2.2
A2 A2 A2 A2 A2
A1 A1 A1 A1
A5 A5 A5 A5 A5
1.1 1.5 2.2
2.4 3 4.1 5.6
3.8 4.8 6.6 9.0
2.1 2.7 3.4 4.8
3.4 4.3 5.4 7.7
1.7 2.1 2.8 3.9
1.7 2.4 2.7 3.8
24 - 10 AWG
2
2.2 2.7 3.7 5.0
3.5 4.3 5.9 8.0
1.9 2.7 3.1 4.3
3.0 4.3 5.0 6.9
10 10 10 10 20
42 46 58 62 88
4.8 4.8 4.9 4.9
13.5 13.5
0.97 0.97
® is a registered Danfoss trademark.
FC 300 Design Guide
3 4 5.5 7.5
A2 A2 A3 A3
A5 A5 A5 A5
3 4 5.5 7.5
7.2 10 13 16
11.5 16 20.8 25.6
6.3 8.2 11 14.5
10.1 13.1 17.6 23.2
5.0 6.9 9.0 11.0
5.0 6.5 8.8 11.6
24 - 10 AWG
0.00031-0.0062 in.
[0.2-4 mm] 2
6.5 9.0 11.7 14.4
10.4 14.4 18.7 23.0
5.7 7.4 9.9 13.0
9.1 11.8 15.8 20.8
20 20 32 32
116 124 187 255
4.9 4.9 6.6 6.6
13.5 13.5 14.2 14.2
0.97 0.97 0.97 0.97