Toshiba Q9 Installation And Operation Manual page 31

RR — The default function assigned to this terminal is the Frequency Mode 1 setting. The RR
terminal accepts a 0 – 10 VDC input signal that is used to control the function assigned to this terminal.
This input terminal may be programmed to control the speed or torque of the motor via an amplitude
setting or regulate by setting a limit. The gain and bias of this terminal may be adjusted for application-
specific suitability (See
terminal. This terminal references CCA.
RX — The RX terminal accepts a ±10 VDC analog input signal and controls the function assigned to
this terminal. This input terminal may be programmed to control the speed, torque, or direction of the
motor. It may also be used to regulate (limit) the speed or torque of the motor by setting a limit. The
gain and bias of this terminal may be adjusted for application-specific suitability (See
See Figure 20 on pg. 24
V/I — The V/I terminal has the dual function of being able to receive an input voltage or current. The
function as a voltage input to receive a 0 – 10 VDC input signal. The function as a current input is to
receive a 0 – 20 mA input signal. Using either input type, the function is to control the 0.0 – Maximum
Frequency output or the 0.0 to 250% torque output of the ASD. This is an isolated input terminal. This
terminal may be programmed to control the speed or torque of the motor and cannot process both input
types simultaneously. SW301 must be set to V or I to receive a voltage or current, respectively (See
Figure 9 on pg.
terminal may be adjusted for application-specific suitability (See
SU+ — Externally supplied +24 VDC ±10% at 1.1 A (minimum) backup control power. This terminal
references CC.
P24 — +24 VDC at 200 mA power supply for customer use. This terminal references CCA.
PP — The function of output PP is to provide a 10 VDC/10 mADC output that may be divided using a
potentiometer. The tapped voltage is applied to the RR input to provide manual control of the RR
programmed function. This terminal references CCA.
O1A/B (OUT1A/B) — The default function assigned to this terminal is
output may be programmed to provide an indication (open or closed) that any one of the functions listed
in Table 7 on pg. 190
(e.g., activate the brake) (See F130). The OUT1 terminal is rated at 2 A/120 VAC and
2 A/30 VDC.
O2A/B (OUT2A/B) — The default function assigned to this terminal is ACC/DEC Complete. This
output may be programmed to provide an indication (open or closed) that any one of the functions listed
in Table 7 on pg. 190
(e.g., activate the brake) (See F131). The OUT2 terminal is rated at 2A/120 VAC and
2A/30 VDC.
FP
— The default function assigned to this open collector output terminal is Output Frequency. This
output terminal produces an output pulse train that has a frequency which is proportional to the
magnitude of the Output Frequency (or the function assigned to this terminal). This terminal may be
programmed to provide an output pulse rate that is proportional to the magnitude of the user-selected
item from Table 6 on pg.
AM — The default function assigned to this output terminal is Output Current. This output terminal
produces an output current that is proportional to the magnitude of the Output Current of the Q9 ASD
(or the function assigned to this terminal). The available assignments for this output terminal are listed
in Table 6 on pg.
FM — This output terminal produces an output current or voltage that is proportional to the output
frequency of the ASD or of the magnitude of the function assigned to this terminal. The available
assignments for this output terminal are listed in
terminal see
Q9 ASD Installation and Operation Manual
F210 – F215). See
for an electrical depiction of the RX terminal.
22). Terminal scaling is accomplished via
has occurred or is active. This function may be used to signal external equipment
has occurred or is active. This function may be used to signal external equipment
189. For further information on this terminal see
189. For further information on this terminal see
F005 on pg. 61. The Voltage/Current output selection is performed at F681.
Figure 20 on pg. 24 for an electrical depiction of the RR
F201 – F206. The gain and bias of this
F470
F670 on pg.
Table 6 on pg. 189. For further information on this
F216 – F221).
and F471).
Damper Command. This
F676 on pg. 143.
141.
21