Siemens SINUMERIK 828D Function Manual page 1787

Mode group stop , 1668
Mode group stop axes plus spindles
Motor being selected
Motor selection A, B
Motor temperature prewarning
n(act) equals n(set) ,
n(act) less than n(min)
n(act) less than n(x) ,
NC Ready , 1613
NC start , 1677
NC start disable , 1677
NC stop , 1678
NC Stop at block limit
NC Stop axes plus spindles
NCK alarm is active ,
NCK alarm with processing stop present
NCK battery alarm , 1615
NCK CPU Ready , 1612
NCU 573 heatsink temperature alarm
OK , 1622
Oscillation controlled by the PLC
,
Oscillation enable 1707
Override active , 1729
Overstore active , 1625
Part program selection
Path axis , 1694
PLC action completed
PLC hard keys , 1618
PLC index , 1619
PLC line offset , 1619
POS_RESTORED 1
POS_RESTORED2 ,
Position controller active
Position measuring systems 1 and 2
Position reached with exact stop coarse
Position reached with exact stop fine
ProgEventDisplay , 1691
Program level abort ,
Program status aborted
Program status interrupted
Program status running
Program status stopped
Program status wait ,
,
Program test active
Pulse enable , 1636
Pulses enabled , 1642
Ramp function generator disable active
Ramp­function generator fast stop
Ramp-up completed
Rapid traverse override
Rapid traverse override active
Read-in disable , 1676
Basic Functions
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
, 1668
, 1635
, 1635
, 1644
1650
, 1650
1650
, 1677
, 1678
1614
, 1624
, 1614
, 1706
, 1618
, 1675
, 1620
, 1701
1701
,
1638
, 1629
, 1657
, 1657
1676
, 1684
, 1684
, 1683
, 1684
1684
1683
, 1640
, 1633
, 1646
, 1721
, 1723
Read-in enable is ignored
Recall alarm cleared , 1621
Reference point approach delay
Reference point value 1 to 4
Referenced/synchronized 1
Referenced/synchronized 2
Referencing active , 1698
Remote diagnosis active
Repos DEFERAL Chan
REPOS Delay Ackn , 1693
REPOS offset , 1692
REPOS offset valid , 1693
Repos Path Mode Ackn0-2
REPOSDELAY , 1692 , 1693
REPOSMODEEDGE , 1679
REPOSMODEEDGEACKN
Reset , 1678
Re-synchronizing spindle when positioning 1 and 2
1705
Resynchronizing spindles 1 and 2
Revolutional feed rate active
,
Rigid tapping active 1713
RMB , 1679
RME , 1679
RMI , 1679
RMN , 1679
RMNOTDEF , 1679
S auxiliary function for spindle
S function for spindle , 1715
Screen bright , 1616
Screen is dark , 1620
Second software limit switch plus or minus
,
Selected JOG mode 1672
Selected machine function REF
Selected mode AUTOMATIC
Selected mode MDA , 1671
Selected mode TEACH IN
Selection , 1623
Sensor for fixed stop , 1659
Sensor S1 available (clamped state)
Sensor S4 (piston end position)
Sensor S4 available (piston position)
Sensor S5 (angular position of the motor shaft)
,
1717 1741
Sensor S5 available (angular position of the motor
shaft) , 1715 , 1739
Sensors available , 1715
Setpoint direction of rotation, counter.clockwise/
setpoint direction of rotation, clockwise
Setpoint gear stage A to C
Setpoint speed increased
Setpoint speed limited ,
Index
, 1686
, 1700
, 1699
, 1700
, 1701
, 1611
, 1691
, 1689
, 1689
, 1704
, 1742
,
1737
, 1666
, 1739
, 1655
, 1672
, 1671
, 1672
, 1715 , 1739
, 1717 , 1741
, 1715 , 1739
,
, 1739
, 1708
, 1709 , 1733
, 1711 , 1735
1710 , 1734
1787
,