Siemens SINUMERIK 828D Function Manual page 1786

Index
AT box ready , 1611
AUTOMATIC mode ,
Axis/spindle disable ,
Axis/spindle stationary
Block search active ,
Block search via program test is active
Cancel alarm cleared
Change gear , 1709 ,
Channel is ready , 1686
Channel number of the machine control panel to
HMI , 1618
Channel status active
Channel status interrupted
Channel status reset
Channel­specific NCK alarm is active
Channel­specific protection zone preactivated
Channel­specific protection zone violated
Clamped state , 1716
Clamping in progress
Clear cancel alarms ,
Clear recall alarms ,
Control program branching
Controller enable , 1630
Controller parameter set switchover (checkback
signal) , 1639
Controller parameter set switchover (request)
Current controller active
D function 1 , 1664
Darken screen , 1616
Delete distance­to­go (axis­specific)/Spindle reset
1632
Delete distance­to­go (channel­specific)
,
Delete S value 1705
Disable parameter set switchover commands from
NC , 1633
displayed channel number from HMI
Drive parameter set selection A, B, C
Drive Ready , 1641
Drive test travel enable
Drive test travel request
Drives in cyclic operation
Drives ready , 1613
Dry run feed rate selected
EMERGENCY STOP
EMERGENCY STOP active
Enable protection zones
Enable travel to fixed stop
Encoder limit frequency exceeded
Error , 1622
Error program handling
Extended address F functions 1 to 6
Extended address H functions 1 to 3
1786
1667
1625
, 1638
1681
, 1688
, 1621
1734
, 1685
, 1685
, 1685
, 1624
, 1654
, 1740
, 1654
1617
1617
,
1692
, 1639
, 1623
, 1622
, 1634
, 1625
, 1637
, 1613
, 1725
,
1696
, 1697
, 1652
, 1660
, 1656
, 1623
, 1665
, 1664
Extended address M functions 1 to 5
Extended address S functions 1 to 3
External zero offset
F auxiliary function for positioning axis
F function for positioning axis
FC9 Out Active
FC9 Out Done
FC9 Out Error
FC9 Out StartError
Feed disable
Feed rate override (axis­specific)
Feed rate override selected for rapid traverse
Feed stop (Geometry axis 1 to 3)
Feed stop/spindle stop (axis­specific)
Feedrate override
, 1653 Feedrate override active
Fixed stop reached
Follow­up mode active
Follow-up mode
Gear is changed over
Hardware limit switches plus and minus
Heat sink temperature pre-warning
HMI battery alarm
HMI CPU1 Ready
HMI temperature limit
, 1633 Interrupt processing active
Invert M3/M4
JOG mode ,
Key disable ,
, Key-operated switch position
Last action block active
Load , 1623
Load part program
Lubrication pulse
M auxiliary function for spindle
M fct. 1-5 not decoded
M function for spindle
M, S, T, D, H, F functions Additional info "Quick"
(quick acknowledgment)
M, S, T, D, H, F functions Modification
M(d) less than M(dx)
M00/M01 active
M02/M30 active
Machine function REF
Machine function REPOS
Machine function TEACH IN
Machine­related protection zone preactivated
Machine­related protection zone violated
MDA mode ,
Mode change disable
Mode group ready
Mode group reset
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
, 1695
, 1742
, 1620
, 1620
, 1620
, 1620
, 1723
, 1727
, 1724
, 1719
, 1724
, 1661
, 1637
, 1628
, 1704
,
, 1612
, 1613
, 1612
, 1686
, 1705
1667
1616
, 1611
, 1681
,
1618
, 1640
, 1666
, 1662
, 1714 , 1738
, 1663
, 1648
, 1680
, 1681
,
1670
, 1669
, 1669
1667
, 1620 , 1668
, 1673
, 1669
, 1663
, 1663
, 1666
, 1725
, 1730
, 1655
1645
, 1662
, 1653
, 1654
Basic Functions