Siemens SINUMERIK 828D Function Manual page 1785

G643 , 163
G644 , 166
G645 , 169
G9 , 150
G91 extension , 1538
Zero point offset , 1539
G93 , 1368
G94 , 1368
G95 , 1368
G96, G961, G97, G971 ,
Gap , 482
gear stage
Manual entry , 1298
Specification by PLC
Gear stage change
Automatic , 1351
gear stages , 1289
Gear step
in M70 , 1321
Geometry axes , 693 , 698
Geometry axes during handwheel traveling
,
GETTCOR 1579
Compatibility , 1584
Orientable toolholder
GETTENV , 1578
GOTOS , 571
Grouping together auxiliary functions
H
H functions , 395
Hardware interrupt , 879
Hardware limit switches
Helical interpolation , 702
Helix interpolation , 702
High-speed data channel
HMI CPU1 Ready , 38
Hold block , 542
Holder angle , 1527
Homing
in rotary absolute encoders
with incremental measurement system
I
IC , 1331
ID check , 670
Implicit continuous­path mode
,
Implicit exact stop 155
Implicit preprocessing stop
Incrementally programmed compensation values
Basic Functions
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
1370
, 1297
, 713
, 834
, 1583
, 416
, 95
, 59
, 1242
, 1207
, 157
, 547
Input resolution
Interface
PLC/HMI , 868
PLC/HMI-Messages
PLC/MCP , 873
PLC/NCK , 862
Interface signals
Acknowledge EMERGENCY STOP
Acknowledge fixed stop reached
Action block active
Activate associated M1
Activate channel­specific protection zone
Activate dry run feed
Activate fixed feed rate 1 - 4 for machine axes
Activate fixed feed rate 1 - 4 for path/geometry axes
1726
Activate M01
activate machine-specific protection zone
Activate program test
Activate referencing
Activate single block
Activate skip block
Activate travel to fixed stop
Active , 1622
Active drive parameter set A, B, C
Active G function of groups 1 to 60
Active JOG mode
Active machine function REF
Active machine function TEACH IN
Active mode AUTOMATIC
Active mode MDA
Active motor A, B
Active or passive file system
Active REPOS machine function
Active spindle control mode
Active spindle mode oscillation mode
Active spindle positioning mode
Actual direction of rotation clockwise
Actual gear stage A to C
Actual value in WCS
Air temperature alarm
All axes stationary
All axes that have to be referenced are referenced
1699
All channels in the reset state
Analog spindle 1, utilization in percent
Analog spindle 2, utilization in percent
Analog value clamped state
Approach block active
Associated M01/M00 active
ASUB is active
, 1538 ASUB is stopped
, 335
, 869
,
, 1659
, 1679
, 1662
, 1718
, 1675
, 1676
, 1698
, 1675
,
1676
, 1660
, 1641
,
, 1673
, 1674
,
, 1673
, 1673
, 1641
,
1619
, 1674
, 1714 , 1738
, 1713
, 1703
, 1617
, 1615
, 1657
, 1674
, 1717 , 1741
, 1680
, 1665
, 1691
, 1688
Index
1696
, 1652
, 1730
,
, 1652
1687
1674
, 1713 , 1737
, 1737
, 1712 , 1736
,
, 1617
, 1618
1785