Precautions In Use; Cautions And Notes - MIMAKI JV150-130 Operation Manual

Safety Precautions

Precautions in Use

Handling of ink
• If you get ink in your eyes, immediately wash your
eyes with a lot of clean water for at least 15 minutes. In
doing so, also wash eyes to rinse ink away completely.
Then, consult a doctor as soon as possible.
• If anyone drinks ink by mistake, keep him or her quiet
and see a doctor immediately. Do not allow him or her
to swallow the vomit.
Then contact the emergency number written in MSDS.
• If you inhale a lot of vapor and feel bad, immediately
move to a location of fresh air and then keep yourself
warm and quiet. Then, consult a doctor as soon as
possible.
• Store ink cartridges in a place that is out of the reach of
children.
• If the ink adheres to your skin, use a large amount of
water and soap or special detergent for skin to remove
the ink.
Handling of the power cable
• Connect to a socket-outlet with determinate polarity.
• For Inlet, be sure to supply power from the outlet of the
same voltage.
• For PLUGGABLE EQUIPMENT, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
• Unplug the cord from the wall outlet and remove dust
from the power plug periodically, at least once a year.
Failure to do so may result in fire or electric shocks.
• Do not use the machine unless it is connected to a
power supply that satisfies the displayed voltage
condition.
• Check the voltage of the wall outlet and the capacity of
the circuit breaker before you plug the power cords.
Plug each power cord to different outlet that has
independent circuit breaker. If you plug more than one
power cord to wall outlets that share the same circuit
breaker, the power may be cut off by the breaker.
Power supply
• Leave the breaker turned ON.
• Do not turn off the main power switch on the right side
of this machine.
Notes When Handling the Main Unit
• Use the equipment in a well-ventilated or not-airtight
room.
• Use the equipment in a well-ventilated or not-airtight
room.
• Ventilate the room sufficiently before using the
equipment.
• Do not place the equipment in a humid or dusty place.
Otherwise, there is a risk of fire or electrical shock.
• Do not place the equipment in an unstable place such
as on a shaky table and on a tilted surface. The
equipment may fall over or drop and cause injury.
• The equipment is provided with a built-in media cutter.
To replace or feed a printing medium, or to remove a
jammed printing medium, do not touch any area other
than those specified in this document. Otherwise,
there is a risk of injury.
vii
CAUTION
CAUTION
• To replace a printing medium, be careful not to pinch
your fingers or get injured.
• Consult with the service shop about cleaning inside the
equipment.
Leaving the equipment with dust inside without
cleaning for a long time may cause a fire or device
failure. Consult with the distributor or service shop for
the cost of cleaning inside the equipment.
• To move the equipment, contact the nearest service
shop.
Note on maintenance
• When cleaning the ink-station or the heads, make sure
to wear the attached goggles and gloves.
• The gloves supplied with the machine are disposable.
When all the gloves are expended, purchase an
equivalent product on the market.
• Do not to touch the sharp edge of the blade when
replacing the cutter. Touching the sharp edge may
result in injury.
• Turn off the machine and unplug the power cord from
the wall outlet for safety when moving the machine.

CAUTIONS and NOTES

Warning
Front cover and lever
• Never open the front cover or raise the lever during printing.
Opening the cover or raising the lever will abort printing.
Protection of media from dust
• Store media in a bag. Wiping off dust accumulated on media
will adversely affect the media due to static electricity.
• When leaving the workshop after the working hours, do not
leave any media on the roll hanger. If any media is left on the
roll hanger, it can get dusty.
Periodic replacement parts
• Some parts of this machine must be replaced with a new
one periodically by service personnel. Be sure to make a
contract with your distributor or dealer for After sale service
to ensure a long life of your machine.
Disposition of this machine
• Consult your sales or service representative for proper disposal
of this machine. Otherwise, commission an industrial waste
disposal company.
Handling of ink cartridges
• The safety evaluation of this machine assumes that the ink
recommended by this company is used. For safe usage of this
machine, use the ink recommend by this company
• Never refill the ink pack and white ink cartridge with ink. Refilled
ink cartridge can cause a trouble. Remember that MIMAKI
assumes no responsibility for any damage caused by the use of
the ink cartridge replenished with ink.
• If the ink cartridge is moved from a cold place to a warm place,
leave it in the room temperature for three hours or more before
using it.
• Open the ink cartridge just before installing it in the machine. If it
is opened and left for an extended period of time, normal
printing performance of the machine may not be ensured.
• Make sure to store ink cartridges in a cool and dark place.
• Store ink cartridges and waste ink bottle in a place that is out of
the reach of children.