MIMAKI JV150-130 Operation Manual page 53

When [Ink Level low] is displayed
When quantity of the remaining 600 cc ink becomes low, a
warning [Ink Level] appears.
Enter the weight of the cartridge with the Ink Level Set
function.
• This machine recalculates usable amount of
remaining ink by entering the weight of the 600 cc
cartridge.
• Ink Level Set function starts by resetting the 600
cc cartridge indicating [Ink Level] warning in the
local mode or remote mode (during waiting or
printing).
• Weight the cartridge exactly down to the gram.
Entering a larger weight than the actual one may
cause Nozzle Drop Out.
 Using Ink Level Set function
1
If [Ink level low] is displayed, remove the
600cc cartridge and measure the weight of
the 600cc cartridge.
• Be sure to measure the weight of the eco case
including the 600 cc ink pack.
I n k L e v e l
Displays the cartridge causing [Ink Level] warning.
Upper line : Ink color being set
Lower line : Cartridge condition
" - " No error
"L" Ink Level Low (low)
"E" Ink Level End (end)
• Use the "E" display as a guide for replacing the ink
pack.
• If ink remains much in the ink pack even when "E"
is displayed, proceed to the Step 2 and the
subsequent steps.
• Ink in the ink pack cannot be completely used up.
To prevent ink supply errors, about 30 cc of ink
must remain in the ink pack.
2
Reset the 600 cc cartridge.
3
Press .
4
Pressi
weight of the 600cc cartridge.
I n k L e v e l S e t
[ 1 ] 0 5 5
Displays the set number of times of weight to the
cartridge being operated.
• Press the [][] keys to move to another digit.
• Press the [][] keys to input the weight.
M M C C Y Y K K
- - L - - - E -
to input the
. . C . . . . .
5 g
Chapter 3 Mchine setting
5
Press the
• Usable amount of remaining ink is recalculated.
• The contents displayed differ depending on the
amount of remaining ink.
(1) When ink still remains
• Return to the local mode or the remote mode.
• [Ink Level] warning disappears and the state
of the 600 cc cartridge that Ink Level Set
function was performed changes to [INK
NEAR END] warning.
• [INK NEAR END] warning can be checked on
the guidance function. (
(2) When no ink remains
• A message for replacing the ink pack is
displayed.
• Press the [ENTER] key to return to the local
mode or the remote mode.
• [Ink Level] warning is still displayed and the
state of the 600 cc cartridge that Ink Level
Set function was performed changes to [INK
END] warning.
• [INK END] warning can be checked on the
guidance function. (
• Once a message for replacing the ink pack
appears, immediately replace the target ink pack
with a new one. (Usable ink has been used up.)
• Ink in the ink pack cannot be completely used up.
To prevent ink supply errors, about 30 cc of ink
must remain in the ink pack. (Before shipping,
more than 630 cc of ink is filled in the ink pack to
use 600 cc.)
 When an error occur in the Step 5
This function stores the calculated quantity of remaining
ink in the ink chip of the 600cc cartridge.
If the 600cc cartridge is removed or there is a problem on
the contact of this device and the ink chip, the data
storage in the ink chip cannot be performed. In this case,
the error message "ERROR 614 Preservation Fail" will be
displayed.
If the message is displayed, reinsert the 600cc cartridge
and follow the procedures from the Step 2 again.
Error when performing maintenance
function
When performing the maintenance function such as the
head cleaning or the ink filling for the 600 cc cartridge,
selected functions can be performed if the quantity of
remaining ink is enough to execute the function, even if
the ink near end occurs.
If the quantity of remaining ink is not enough, a error
message "ERROR 614 Preservation Fail" appears, and
selected maintenance function is not performed.
key twice.
P.3-27)
P.3-27)
3-15
1
2
3
4
5
6