Toshiba TOSVERT VF-AS1 Instruction Manual page 11

5.16 Meter setting and adjustment························································································································
5.17 PWM carrier frequency ·································································································································
5.18 Trip-less intensification ·································································································································
5.18.1 Auto-restart (Restart during coasting)····································································································
5.18.2 Regenerative power ride-through control/Deceleration stop during power failure/
Synchronized acceleration/deceleration·······································································································
5.19 Dynamic (regenerative) braking - For abrupt motor stop ··············································································
5.20 Standard default setting ································································································································
5.21 Searching for all reset parameters and changing their settings ····································································
5.22 EASY key function ········································································································································
6. Extended parameters···········································································································································
6.1 Input/output parameters································································································································
6.1.1 Low-speed signal···································································································································
6.1.2 Putting out signals of arbitrary frequencies····························································································
6.2 Input signal selection ····································································································································
6.2.1 Priority when forward/reverse run commands are entered simultaneously············································
6.2.2 Assigning priority to the terminal board in the operation panel and operation mode ·····························
6.2.3 Analog input signal switching·················································································································
6.3 Terminal function selection····························································································································
6.3.1 Keeping an input terminal function always active (ON)··········································································
6.3.2 Modifying input terminal functions ·········································································································
6.3.3 Using the servo lock function·················································································································
6.3.4 Modifying output terminal functions ·······································································································
6.3.5 Response time of input/output terminals································································································
6.4 Basic parameters 2 ·······································································································································
6.4.1 Switching among V/f characteristics 1, 2, 3 and 4 from input terminal···················································
6.5 V/f 5-point setting··········································································································································
6.6 Speed command switching ···························································································································
Using two types of frequency (speed) commands ·················································································
6.6.1
6.7 Operation frequency ·····································································································································
6.7.1 Start frequency/Stop frequency··············································································································
6.7.2 Run/Stop control with frequency setting signals ····················································································
6.7.3 Frequency setting signal 0Hz dead zone handling function···································································
6.8 DC braking····················································································································································
6.8.1 DC braking·············································································································································
6.8.2 Motor shaft fixing control························································································································
6.8.3 Function of issuing a 0Hz command during a halt ·················································································
6.9 Auto-stop in case of lower-limit frequency continuous operation ··································································
6.10 Jog run mode················································································································································
6.11 Setting frequency via external contact input (Up/Down frequency setting) ···················································
6.12 Jump frequency - jumping resonant frequencies ··························································································
6.13 Preset speed operation frequencies ·············································································································
6.13.1 Preset speed operation frequency 8 to 15 ·····························································································
6.13.2 Forced oeration control··························································································································
6.14 Trip-less intensification ·································································································································
6.14.1 Retry function ········································································································································
6.14.2 Avoiding overvoltage tripping·················································································································
6.14.3 Output voltage adjustment/Supply voltage correction············································································
6.14.4 Reverse run prohibition··························································································································
6.15 Drooping control ···········································································································································
6.16 Light-load high-speed operation function ······································································································
6.17 Braking function ············································································································································
6.18 Acceleration/deceleration suspend function··································································································
6.19 Commercial power/inverter switching ···········································································································
6.20 PID control ····················································································································································
6.21 Stop position control function ························································································································
6.22 Setting motor parameters ·····························································································································
ii
E6581528
E-27
E-31
E-32
E-32
E-34
E-37
E-42
E-46
E-47
F-1
F-1
F-1
F-2
F-3
F-3
F-4
F-5
F-6
F-6
F-6
F-8
F-8
F-9
F-9
F-9
F-11
F-11
F-11
F-13
F-13
F-13
F-14
F-14
F-14
F-16
F-17
F-18
F-19
F-20
F-22
F-23
F-23
F-23
F-24
F-24
F-25
F-25
F-27
F-27
F-28
F-29
F-31
F-32
F-33
F-34
F-34