Toshiba TOSVERT VF-AS1 Instruction Manual page 13

6.36.7 Setting of a torque command in panel operation mode ·········································································
6.36.8 Torque-related parameters for panel operation······················································································
6.37 Tracing functions···········································································································································
6.38 Integral output power ····································································································································
6.39 Communication function ·······························································································································
6.39.1 2-wire RS485/4-wire RS485 ··················································································································
6.39.2 Open network option······························································································································
6.40 My function ···················································································································································
6.41 Traverse function ··········································································································································
6.42 Instruction manuals for optionally available devices and special functions···················································
7. Operation with external signal······························································································································
7.1 External operation·········································································································································
7.2 Applied operation with input and output signals (operation by terminal board) ·············································
7.2.1 Functions of input terminals (in case of sink logic) ················································································
7.2.2 Functions of output terminals (incase of sink logic) ···············································································
7.2.3 Setup of input terminal operation time ···································································································
7.2.4 Analog input filter···································································································································
7.3 Setup of external speed command (analog signal)·······················································································
7.3.1 Setup by analog input signals (RR/S4 terminal) ····················································································
7.3.2 Setup by analog input signals (VI/II terminal) ························································································
7.3.3 Setup by analog input signals (RX terminal)··························································································
8. Monitoring the operation status····························································································································
8.1 Screen composition in the status monitor mode ···························································································
8.2 Monitoring the status·····································································································································
8.2.1 Status monitor under normal conditions·································································································
8.2.2 Display of detailed information on a past trip ·························································································
8.3 Changing status monitor function··················································································································
8.4 Display of trip information ·····························································································································
8.4.1 Trip code display····································································································································
8.4.2 Monitor display at tripping······················································································································
8.5 Display of alarm, pre-alarm, etc. ···················································································································
9. Measures to satisfy the standards························································································································
9.1 How to cope with the CE standard················································································································
9.1.1 EMC directive ········································································································································
9.1.2 Measures to satisfy the EMC directive···································································································
9.1.3 Low-voltage directive ·····························································································································
9.1.4 Measures to be taken to satisfy the low-voltage directive······································································
9.2 Measures to be taken to satisfy the UL/CSA standards ················································································
9.2.1 Caution in installing the inverter·············································································································
9.2.2 Caution in wiring and rated current········································································································
9.2.3 Caution as to peripheral devices ···········································································································
9.2.4 Caution as to the protection of motors from overload ············································································
9.3 Compliance with safety standards ················································································································
10. Selection of peripheral devices ····························································································································
10.1 Selection of wiring materials and devices ·····································································································
10.2 Installation of a magnetic contactor···············································································································
10.3 Installation of an overload relay ····················································································································
10.4 Application and functions of options ·············································································································
10.5 Optional internal devices·······························································································································
10.6 Connection of a DC power terminals ············································································································
11. Table of parameters ·············································································································································
iv
E6581528
F-72
F-73
F-73
F-76
F-77
F-77
F-83
F-83
F-84
F-84
G-1
G-1
G-2
G-2
G-5
G-9
G-9
G-10
G-11
G-12
G-13
H-1
H-1
H-2
H-2
H-5
H-6
H-8
H-8
H-10
H-12
I-1
I-1
I-1
I-2
I-3
I-3
I-4
I-4
I-4
I-4
I-5
I-6
J-1
J-1
J-5
J-5
J-6
J-9
J-12
K-1