Philips DVDR615 Service Manual page 72

http://www.jdwxzlw.com/?fromuser=华盛维修
EN 72 5.
5.4 DVD Module Error code
With DSW command 910 the set software can retrieve an
overview of all occurred engine errors.
5.4.1 Momentary Errors
Byte 0: latest error:
Overview of the BE error codes.
error error
code
0x00 no_error
0x01 illegal_command_error
0x02 illegal_parameter_error
0x03 command_timeout_error
0x04 sledge_home_error
0x05 sledge_calibration_error
0x06 sledge_unstable_error
0x07 speed_timeout_error
0x08 speed_window_error
0x09 focus_timeout_error
0x0A focus_retries_error
0x0B focus_agc_error
0x0C radial_timeout_error
0x0D radial_retries_error
0x0E radial_agc_error
0x0F radial_init_error
0x10 hf_pll_error
0x11 wobble_pll_error
0x12 subcode_timeout_error
0x13 subcode_notfound_error
0x14 header_timeout_error
0x15 adip_timeout_error
0x16 adip_window_error
0x17 adip_sync_error
家电维修资料网，免费下载各种维修资料
DVDR615/69 Diagnostic Software
meaning
No error has occurred
Command not allowed in this
state or unknown command
Parameter(s) not valid for this
command
The maximum execution time for
the command has exceeded
The sledge could not be moved
home
An error occurred during calibra-
tion of the sledge
The sledge detected unstable
control
Spindle motor could not reach its
target speed within timeout
Measured spinning speed is not
within expected window
Focus could not be achieved
within the timeout
The amount of focus retries ex-
pired
The focus agc results are out of
range
Servo didn't get on track within
the timeout
Servo didn't get on track after
several retries
The radial agc results are out of
range
Unreliable signal scaling after the
radial initialisation
HF-decoder pll could not lock to
HF signal
Wobble pll could not lock to wob-
ble signal
Subcode information could not
be read
Requested subcode item could
not be found
Header information could not be
read
Adip information could not be
read
Adip address was not within ex-
pected window
No adip sync was detected
error error
code
0x18 atip_timeout_error
0x19 atip_notfound_error
0x1A atip_window_error
0x1B atip_sync_error
0x1C tray_error
0x1D seek_error
0x1E no_hf_present_error
0x1F record_error
0x20 illegal_stopaddress_error
0x21 no_disc_error
0x22 not_initialised_error
0x23 illegal_medium_error
0x24 cd_frequency_error
0x25 dvd_frequency_error
0x26 re-
served(non_existing_bca_
error)
0x27 reserved(bca_read_error) An error occurred during reading
0x28 selftest_error
0x29 i2c_error
0x2A laser_pll_error
0x2B laser_forward_sense_erro
r
0x2C jitter_optimisation_error
0x2D tilt_calibration_error
0x2E reserved
0x2F frontend_offset_calib_erro
r
0x30 reserved
0x31 wsg_calculation_error
0x32 buffer_overrun_error
0x33 return_value_invalid_error The requested information is not
0x34 illegal_recording_speed_e
rror
0x35 opc_media_parameter_err
or
0x36 opc_record_power_error
0x37 opc_start_power_low_erro
r
0x38 opc_start_power_high_err
or
meaning
Atip information could not be
read
Requested atip item could not be
found
Atip address was not within ex-
pected window
No atip sync was detected
Tray could not be closed or
opened within the timeout
The requested seek couldn't be
performed within the timeout
Attempt to read from a blank area
An error occurred during the re-
cording
The requested stopaddress with
modify-stop-address is not valid
No disc is detected
The system is not initialised (e.g.
seek on unknown disctype)
BE detected an unsupported me-
dium during disc recognition
Measured HF frequency is not
within CD frequency range
Measured HF frequency is not
within DVD frequency range
Attempt to read non-existing bca
information
of bca information
An error occurred during the self-
test of the BE
The I2C interface does not oper-
ate
Laser control pll did not lock or
lost lock on write clock
Forward sense value didn't
change with changing laser pow-
er
An error occurred during optimis-
ation of the jitter
An error occurred during calibra-
tion of the tilt frame
The offset in the frontend couldn't
be calibrated
An error occurred in the calcula-
tion of the write strategy
The buffer input stream overran
the buffer output stream
available for this inquiry
The selected speed is not al-
lowed for a recording on this me-
dium
The media parameters (info in
ATIP/ADIP) are invalid or not
read
The final optimum power was not
reached
OPC start power too low (opti-
mum power is higher)
OPC start power too high (opti-
mum power is lower)