Troubleshooting; Technical Data - Stanley STHT-12183 Technical Data Manual

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.

TROUBLESHOOTING

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
l Disconnect the tool from the air supply and empty the magazine completely before proceeding.
l If the problem cannot be resolved using the guide below, Contact your nearest Stanley representative or distributor.
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
PROBLEM
Failure to cycle
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
Lack of power; slow to cycle
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
udgør ikke CE overholdelse for produkterne.
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
Trigger valve housing leaking air.
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
Trigger valve stem leaks air
Frame/nose leaks air
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
Frame/cap leaks air
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
τα προϊόντα.
Skipping fasteners; intermittent feed
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
documento non garantiscono la conformità CE per i relativi prodotti.
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
dokumentet oppfyller ikke kravene for CE-merking for produktet.
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
deste documento não estão em conformidade com a CE para os produtos.
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
Fasteners jam in tool
S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

TECHNICAL DATA:

Please look at the technical table marked * at the end of this manual.
prezentowanych produktów.
A Length mm.
B Height mm.
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
C Width mm.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
D Weight Kg.
prezentowanych produktów. E Noise L , 1s, d
pa
F Noise L
wa
G Noise L , 1s, 1m
pa
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
H Vibration m/s
dokumentu nie sú v súlade s CE pre dané výrobky.
I P max Bar
J P min Bar
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
CAUSE
Air supply restriction
Tool dry, lack of lubrication
Worn head valve O-rings (if present)
Broken cylinder cap spring
Head valve (if present) stuck in cap
Air pressure too low
Tool dry, lacks lubrication
Broken cylinder cap spring
O-rings/seals cut or cracked
Exhaust blocked
Trigger assembly worn/leaks
Cylinder sleeve not seated correctly on bottom bumper Disassemble to correct
Head valve dry
O-ring cut or cracked
O-rings/seals cut or cracked
O-ring or gasket is cut or cracked
Bumper cracked/worn
Damaged gasket or seal
Cracked/worn head valve bumper
Loose cap screws
Worn bumper
Air restriction/inadequate air flow through quick
disconnect socket and plug
Worn piston O-ring (if present)
Tool dry, lacks lubrication
Damaged pusher spring
Low air pressure
Loose magazine nose screws
Fasteners too short for tool
Bent fasteners
Wrong size fasteners
Leaking head cap gasket
Trigger valve O-ring cut/worn
Broken/chipped driver
Dry/dirty magazine
Worn magazine
Driver channel worn
Wrong size fasteners
Bent fasteners
Loose magazine/nose screws
Broken/chipped driver
, 1s, d
2
CORRECTION
Check air supply equipment
Use STANLEY BOSTITCH Air Tool Lubricant
Replace O-rings
Replace cylinder cap spring
Disassemble/Check/Lubricate
Check air supply equipment
Use STANLEY BOSTITCH Air Tool Lubricant
Replace cylinder cap spring
Replace O-rings/seals
Check bumper, head valve spring, muffler
Replace trigger assembly
Disassemble/lubricate
Replace O-ring
Replace O-rings/seals
Replace O-ring or gasket
Replace bumper
Replace gasket or seal
Replace bumper
Tighten and recheck
Replace bumper
Replace quick disconnect fittings
Replace O-ring, check driver
Use STANLEY BOSTITCH Air Tool Lubricant
Replace spring
Check air supply system to tool
Tighten all screws
Use only recommended fasteners
Discontinue using these fasteners
Use only recommended fasteners
Tighten screws/replace gasket
Replace O-ring
Replace driver (check piston O-ring)
Clean/lubricate use STANLEY BOSTITCH Air Tool Lubricant
Replace magazine
Replace nose/check door
Use only recommended fasteners
Discontinue using these fasteners
Tighten all screws
Replace driver (check piston O-ring)
K Air consumption per shot @ 5.6 Bar
L Activation type
M Summer lubricant
N Winter lubricant
O O-ring lubricant
P Fastener Name
Q Dimensions mm.
R Head/crown
S Magazine capacity
T New Driver Length mm.
U Max. Depth Inside Piston mm.