Tool Operation Check; Loading The Tool - Stanley STHT-12183 Technical Data Manual

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
advantage because it will not accidentally drive a fastener
if the tool is contacted against the work - or anything else -
F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
while the operator is holding the trigger pulled.
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
Before handling or operating this tool:
Read and understand the warnings contained in this manual.
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Refer to the Tool Technical Data to identify the operating
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
system on your tool.

TOOL OPERATION CHECK

NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
CAUTION: Remove all fasteners from tool before performing
tool operation check.
DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
TRIGGER OPERATED TOOL:
udgør ikke CE overholdelse for produkterne.
A) With the finger off the trigger, hold the tool with a firm grip
on the handle.
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
B) Place the nose of the tool against the work surface.
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
C) Pull the trigger to drive a fastener. Release the trigger and
the cycle is complete.
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
Caution: The tool will cycle each time the trigger is pulled!
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
SEQUENTIAL TRIP OPERATION
τα προϊόντα.
A) Without touching the trigger, press the safety trip against
the work surface.
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
THE TOOL MUST NOT CYCLE.
documento non garantiscono la conformità CE per i relativi prodotti.
B) Hold the tool off the work surface and, avoiding to point
the tool at self or others, pull the trigger.
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
THE TOOL MUST NOT CYCLE.
dokumentet oppfyller ikke kravene for CE-merking for produktet.
C) With the tool off the work surface, pull the trigger. Press
the safety trip against the work surface
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
THE TOOL MUST NOT CYCLE.
deste documento não estão em conformidade com a CE para os produtos.
D) Without touching the trigger, press the safety trip against
the work surface then pull the trigger.
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
THE TOOL MUST CYCLE.
m TOOL USE
S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
Having checked that the tool is working properly, press the
documento no suponen la conformidad con las normas CE de los productos.
nose against the work piece and pull the trigger. Check
whether the fastener has been driven as required.
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
l If the fastener is not driven deep enough, increase the
air pressure by 5-6 psig. (0.5 Bar) at a time, checking the
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
result after each adjustment. Do not exceed the maximum
prezentowanych produktów.
permissible working pressure (see Tool Technical Data)
l If the fastener is driven too deeply, reduce the air pressure
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
by 5-6 psig (0.5 Bar) at a time, checking the result after
each adjustment. Do not try to use less than the minimum
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
working pressure (see Tool Technical Data).
prezentowanych produktów.
Always try to work with the lowest possible air pressure. This
will reduce the noise and vibration produced and will extend
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
the life of the internal components such as the bumper.
dokumentu nie sú v súlade s CE pre dané výrobky.
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

LOADING THE TOOL:

STHT1-12184 (APC-BN) & STHT1-12185 (APC-2IN1)
l Depress magazine release button and pull back magazine.
(Fig 1)
l With magazine fully open, insert fasteners. Points must be
against bottom of magazine. (Fig 2a & 2b)
l Push magazine forward. (Fig 3)
l Continue pushing until latch is engaged. (Fig 4)
STHT1-12183 (APC-FN)
l Open the magazine: pull pusher back to engage latch. (Fig 1)
l With magazine fully open, insert fasteners from rear. Points
must be against bottom of magazine. (Fig 2).
l Close magazine: release latch by pulling latch tab and
pusher together slightly to disengage. Slide pusher against
the nails. (Fig 2 & 3)
FASTENER CONTROL ADJUSTMENT- STHT1-12184 (APC-BN) /
STHT1-12185 (APC-2IN1) / STHT1-12183 (APC-FN) (FIG 5)
Fastener control adjustment feature provides close control
of the fastener drive depth; from flush with the work surface
to shallow or deep counter sink. First, set the air pressure
for consistent drive in the specific work, then use the control
adjustment to give the desired depth of drive.
JAM RELEASE- STHT1-12185 (APC-2IN1) /
STHT1-12183 (APC-FN) (FIG 6).
Warning: Always disconnect the air before clearing a jammed
fastener.
1. Depress the latch button
2. With the latch button depressed, rotate the latch assembly
upwards and forwards until latch is on upward position.
3. Clear jam
ADJUSTING THE MULTI-DIRECTIONAL EXHAUST
STHT1-12185 (APC-2IN1) / STHT1-12183
(APC-FN) / STHT1-12184 (APC-BN) (FIG 7)
To adjust the multi-directional exhaust simply rotate the
exhaust deflector to the desired position as illustrated by the
arrows.