Air Supply And Connections; Sequential Trip - Stanley STHT-12183 Technical Data Manual

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
m SAFETY INSTRUCTIONS FOR TOOL OPERATION
F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
Always handle the tool with care: 1) Never engage in horseplay;
2) Never pull the trigger unless nose is directed towards the
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
work; 3) Keep others at a safe distance from the tool while tool
is in operation as accidental actuation may occur, possibly
causing injury.
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
The operator must not hold the trigger pulled on safety trip tools
except during fastening operation as serious injury could result
if trip accidentally contacts someone or something, causing tool
NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
to cycle.
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
Keep hands and body away from the discharge area of the
tool. A safety trip tool may bounce from the recoil of driving
a fastener and an unwanted second fastener may be driven
DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
possibly causing injury.
udgør ikke CE overholdelse for produkterne.
Check operation of the safety trip mechanism frequently. Do not
use the tool if the arm is not working correctly as accidental
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
driving of a fastener may result. Do not interfere with the proper
operation of the safety trip mechanism.
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
Do not drive fasteners on top of other fasteners as this may
cause deflection of fasteners which could cause injury.
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
Do not drive fasteners close to the edge of the work piece as the
wood may split allowing the fastener to be deflected possibly
τα προϊόντα.
causing injury.
m SAFETY INSTRUCTIONS FOR TOOL MAINTENANCE
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
When working on air tools note the warnings in this manual, and
documento non garantiscono la conformità CE per i relativi prodotti.
on the tool itself and use extra care when evaluating problem
tools.
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
m AIR SUPPLY AND CONNECTIONS
dokumentet oppfyller ikke kravene for CE-merking for produktet.
When connecting tools to the air supply, the fastener discharge
area of the tool should be pointed away from the operator and
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
others in the working area. Place the discharge area of the tool
over a test piece of material of sufficient thickness which will
deste documento não estão em conformidade com a CE para os produtos.
fully accommodate the dimensions of the fastener to be driven.
With limbs and body clear of the discharge area the tool the air
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
supply may now be connected.
documento no suponen la conformidad con las normas CE de los productos.
l C ompressors must be adequately dimensioned to ensure
sufficient pressure and volumetric flow for the expected
use. Pressure drops in the air supply can reduce the tool's
S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
driving power. Refer to the Tool Technical Data for setting
documento no suponen la conformidad con las normas CE de los productos.
the correct pressure for the tool.
l T he pressure regulator must have an operating pressure
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
range of 0-8.79 bar.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
l A ir hoses should have a minimum of 10.6 Bar working
pressure rating or 150 percent of the maximum pressure that
prezentowanych produktów.
could be provided in the air system. The supply hose should
contain a fitting that will supply "quick disconnecting" from
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
the male plug on the tool.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
l E nsure that the pressure supplied to the tool does not
prezentowanych produktów. exceed the maximum allowable working pressure, called
ps max. (see Tool Technical Data), Initially set the supply
pressure to the lowest recommended working pressure (see
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
Tool Technical Data).
dokumentu nie sú v súlade s CE pre dané výrobky.
l C heck that the tool is functioning correctly by applying the
nose to a piece of scrap wood and pulling the trigger once or
twice.
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
m LUBRICATION
l F requent, but not excessive lubrication is required for best
performance. Oil added through the air line connection
will lubricate the internal parts. For details of the correct
lubricant see the Tool Technical Data. Do not use detergent
oil or additives as these lubricants will cause accelerated
wear to the seals and bumpers in the tool, resulting in poor
tool performance and frequent tool maintenance.
l I f no airline lubricator is used, add oil during use into the
air fitting on the tool once or twice a day. Only a few drops
of oil (3-5) at a time are necessary. Too much oil will only
collect inside the tool and will be noticeable in the exhaust
cycle.
l C old weather operation- For cold weather operation, near
and below freezing, the moisture in the air line may freeze
and prevent the tool operation.
Caution! - To prevent frost or ice formation on the tool's
operating valves and mechanisms that could cause tool
failure, do not store the tool in a cold weather
environment.
m OPERATION
TO PREVENT ACCIDENTAL INJURIES:
l Never place a hand or any other part of the body in
fastener discharge area of toll while the air supply is
connected.
l Never point the tool at anyone else.
l Never engage in horseplay.
l Never pull the trigger unless nose is directed at the work.
l Always handle the tool with care.
l Do not pull the trigger or depress the trip mechanism while
loading the tool.
TOOLS WITHOUT A SAFETY TRIP
TRIGGER OPERATED (Reference 3 in Technical Data Table,
column L)
The Trigger Operated model is cycled by actuation of the
trigger only. This model does not have a safety trip and is
intended for use only where a safety trip CANNOT be used
to satisfy the requirements of the application. The Trigger
Operated Tool will cycle each time the trigger is actuated.
TOOLS WITH A SAFETY TRIP
All tools with a safety trip are marked with an inverted
equilateral triangle (t). Do not attempt to use a tool marked
in this way if the safety trip is missing or appears damaged.
SEQUENTIAL TRIP (Reference 2 in Technical Data Table,
column L)
The sequential trip requires the operator to hold the tool
against the work with the safety trip depressed before pulling
the trigger. In order to drive additional fasteners, the trigger
must be released and the tool lifted away from the work,
before repeating the above mentioned steps. This makes
accurate fastener placement easier, for instance on framing,
toe nailing and crating applications. The sequential trip allows
exact fastener location without the possibility of driving
a second fastener on recoil, as described under Contact
Trip (below). The sequential trip tool has a positive safety