Safety Instructions; Limited Warranty - Stanley STHT-12183 Technical Data Manual

Table of Contents

Advertisement

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
m SAFETY AND OPERATION MANUAL
F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
Stanley tools are precision built. They will deliver efficient,
dependable service when used correctly and with care. As
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
with any fine power tool, the manufacturer's instructions
must be followed for best results. Please study this manual
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
and understand the safety warnings and cautions before
operating the tool. The instructions on installation, operation
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
and maintenance should be read carefully and the manuals
kept for reference. Note: Additional safety measures may be
required because of your particular application of the tool.
NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
Contact your Stanley representative or distributor with any
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
questions concerning the tool and it's use.
NOTE:
DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
Stanley tools have been designed to provide excellent
customer satisfaction and are designed to achieve maximum
udgør ikke CE overholdelse for produkterne.
performance when used with precision Stanley fasteners
engineered to the same exacting standards.
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
Stanley cannot assume responsibility for product
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
performance if any of our tools are used with fasteners
or accessories not meeting the specific requirements
established for genuine Stanley nails, staples and
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
accessories.
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

LIMITED WARRANTY

τα προϊόντα.
Stanley Inc., warrants to the original retail purchaser that this
product is free from defects in material and workmanship, and
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
agrees to repair or replace, at Stanley's option, any defective
product within 90 days from the date of purchase. This
documento non garantiscono la conformità CE per i relativi prodotti.
warranty is not transferable. It only covers damage resulting
from defects in material or workmanship, and it does not
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
cover conditions or malfunctions resulting from normal wear,
neglect, abuse or accident.
dokumentet oppfyller ikke kravene for CE-merking for produktet.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. ANY WARRANTY OF MERCHANTABILITY OR
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE
deste documento não estão em conformidade com a CE para os produtos.
DURATION OF THIS WARRANTY.
STANLEY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
CONSEQUENTIAL DAMAGES.
documento no suponen la conformidad con las normas CE de los productos.
Some countries do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations
S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
or exclusions may not apply to you. This warranty gives you
documento no suponen la conformidad con las normas CE de los productos.
specific legal rights, and you may also have other rights
which vary from state to state or from country to country.
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
To obtain warranty service, you must return the product at
your expense together with proof of purchase to a Stanley
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
regional warranty repair center.
prezentowanych produktów.
SPECIAL REFERENCES
Only those fasteners that are specified in the operating
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
instructions (see Tool Technical data) should be used in the
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
tool. The tool and the specified fasteners are to be considered
as one single safety system for safety purposes.
prezentowanych produktów.
Repairs shall only be carried out by the authorized agents of
Stanley or by other experts, giving due regard to the safety,
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
operating and maintenance instructions in this manual, the
dokumentu nie sú v súlade s CE pre dané výrobky.
specific tool manual and in the Tool Technical Data.
Note: Experts are those who, as a result of professional
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
training or experience, have acquired sufficient expertise in
the field of fastener driving tools as to be able to assess the
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
safe condition of fastener driving tools.
m SAFETY INSTRUCTIONS
EYE PROTECTION which
provides protection against
flying particles both from
the FRONT and SIDE should always be
worn by the tool operator and others in
the work area when loading, operating
or servicing this tool. Eye protection is
required to guard against flying fasteners
and debris, which could cause severe
eye injury. The employer and/or user must
ensure that proper eye protection is worn.
Eye protection in accordance with 89/686/EEC, and with
equal or greater grade than defined in EN166 should be
used. However all aspects of operators work, environment
and other type/s of machinery being used, should also
be considered when selecting any personal protection
equipment.
CAUTION: ADDITIONAL SAFETY PROTECTION may be
required in some environments. For example, the working
area may include exposure to noise levels that can lead to
hearing damage.
m SAFETY INSTRUCTIONS FOR AIR SUPPLY AND CONNECTIONS
When connecting tools to the air supply, the fastener discharge
area of the tool should be pointed away from the operator and
others in the working area. Place the discharge area of the tool
over a test piece of material of sufficient thickness which will
fully accommodate the dimensions of the fastener to be driven.
With hands clear of the trigger and trip mechanism, limbs and
body clear of the discharge area the tool the air supply may now
be connected.
l D o not use oxygen and combustible gases as an energy
source for pneumatically operated tools.
l D o not use bottled gases or an air supply where the
maximum pressure in the line can potentially exceed 9.6
Bar as the tool may burst, possibly causing injury. If the
maximum air supply pressure could exceed these pressures,
then a pressure reducing valve with a downstream safety
valve shall be built into the air supply.
l D o not pull the trigger or depress the safety trip while
connecting to the air supply. The tool could cycle, possibly
causing injury.
l T he connector on the tool must not hold pressure when the
air supply is disconnected. If a wrong fitting is used, the
tool can remain charged with air after disconnecting and
thus will be able to drive a fastener even after the air line is
disconnected possibly causing injury.
l A lways disconnect air supply: 1) Before making adjustments;
2) When servicing the tool; 3) When clearing a jam; 4) When
tool is not in use; 5) When moving to a different work area,
as accidental actuation may occur, possibly causing injury.
m SAFETY INSTRUCTIONS FOR LOADING TOOL
When loading the tool 1) Never place a hand or any part of the
body in fastener discharge area of the tool; 2) Never point the
tool at self or anyone else; 3) Do not pull the trigger or depress
the safety trip as accidental actuation may occur, possibly
causing injury.
GB

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Stht1-12184Stht1-12185

Table of Contents