Subscribe to Our Youtube Channel
Related Manuals for Stanley SD67
Summary of Contents for Stanley SD67
- Page 1 SD67 HYDRAULIC SPIKE DRIVER USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 17488 7/2017 Ver. 10...
- Page 2 2 ► SD67 User Manual...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest certified dealer, call Stanley Hydraulic Tools at (503) 659-5660 and ask for a Customer Service Representative. SD67 User Manual ◄ 3... -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel. 4 ► SD67 User Manual... -
Page 5: Safety Precautions
If so, place the added precautions in the space provided in this manual. The SD67 Hydraulic Spike Driver will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and understand this manual and any stickers and tags attached to the tool and hoses before operation. -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► SD67 User Manual... -
Page 7: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► SD67 User Manual... -
Page 9: Htma / Ehtma Requirements
(103 bar) (103 bar) (103 bar) System relief valve setting 2495 psi 2000 psi 2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: SD67 User Manual ◄ 9... -
Page 10: Operation
OPERATING PROCEDURES 1. Observe all safety precautions. 2. Move the hydraulic circuit control valve to the ON position. 3. Place the spike driver foot firmly on the spike to be driven. 10 ► SD67 User Manual... -
Page 11: Tool Protection & Care
• Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a minimum working pressure rating of 2500 psi/175 bar. • Permit only experienced personnel to perform tool repair. -
Page 12: Troubleshooting
Remove, clean and replace as driver foot. required. Spike driver operates slow. Low oil flow from power unit. Check power source for proper flow. High back pressure. Check hydraulic system for excessive back pressure and correct as required. 12 ► SD67 User Manual... -
Page 13: Charging The Accumulator
1-1/2 turns. 8. Turn the gauge end of the tester fully counterclockwise 2. Holding the chuck end of the Stanley tester (P/N to retract the plunger in the chuck. Remove the 02835), turn the gauge fully counterclockwise to tester from the charger valve. -
Page 14: Specifications
Special spikes listed below may require the use of a special spike drive foot with changeable cups. Order spike drive foot based on model. Stanley recommends that this change be performed by a authorized service center. Spike Driver Foot (Standard) for screw on cups (Models SD67101, SD67101B) ..........23342 Spike Driver Foot (Extended) for screw on cups (Models SD67141, SD67141B).......... -
Page 15: Sd67 Parts Illustration
SD67 PARTS ILLUSTRATION SD67 User Manual ◄ 15... -
Page 16: Sd67 Parts List
73187 SPIKE DRIVER FOOT MODEL DESCRIPTIONS EXTENDED SOLID SD67101 & SD67101B: Anti-Vibration Handles and 16732 O-RING * Standard (Short) Solid Foot. 20498 COMPRESSION COIL SPRING SD67141 & SD67141B: Anti-Vibration Handles and Extended (Long) Solid Foot. 16 ► SD67 User Manual... - Page 20 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...
Need help?
Do you have a question about the SD67 and is the answer not in the manual?
Questions and answers