Table of Contents
Advertisement
STRATAGY
4/6/24
INSTALLATION
AND
MAINTENANCE
MANUAL
SEPTEMBER
1994
To access the options (Users, Reports, etc.), press
Alt
and the first character
(highlighted)
of the option.
The
default
password
is Stratagy,
with the first
letter
uppercase.
For detailed information
about using the Main
Menu,
see the
Programming
section,
Chapter
3
"Accessing and Using Stratagy."
3 LOCAL ACCESS
Local access refers to accessing
the Stratagy
system
directly via a cable connecting
the Stratagy system with a
laptop or PC. This section discusses:
q Connecting
the cable
4
Preparing the local system
n Using Stratagy locally
3.1
CONNECTING
THE CABLE
Connect
a null modem
cable from COMl
or COM2 on
the laptop/PC
to the Stratagy
system
COM port. The
default setting is COM2 for both the Stratagy
4 and 6.
(See Chapter
3, "Installing
the Hardware,"
Figure
3-6,
"Stratagy 4 and 6 Front and Back Panels.") The Stratagy
24, which
has direct
access
with the monitor
and
keyboard, is not configured
for local access.
On the laptop/PC,
the COM ports are serial ports (g-pin
or 25pin
male connectors).
On the Stratagy
system,
COM2 has a 25pin
male connector.
You may need to
use an adapter with the null modem cable to connect the
laptop/PC to the Stratagy system.
3.2
PREPARING
THE LOCAL
SYSTEM
Preparing
a laptop/PC
involves
loading
the Stratagy
Remote software.
IMPORTANT
NOTE:
Do not install
the Stratagy
Remote
software
on a system
with a screen
saver
program;
Local access may not work.
Load the Stratagy Remote software on the laptop/PC:
1.
2.
3.
4.
4-2
If you are not at the DOS prompt (C:\), exit to the
DOS prompt.
If you are running Windows,
exit Windows.
Do not
use Windows' MS-DOS Prompt option.
Insert the disk that contains the Stratagy
Remote
software into the disk drive.
From the DOS prompt (C:\), enter:
COPY A:REMOTE
This copies the Stratagy
Remote
software
to the
laptop/PC's
disk drive C:. (This example
assumes
that your floppy drive is disk drive A:)
When the copy is complete,
remove the diskette.
3.3
USING
STRATAGY
LOCALLY
L
This section discusses
how to use the Stratagy system
from a local laptop/PC, including access and disconnect.
3.3.1
ACCESSING STRATACY USING A LOCAL
LAPTOP/PC
To access
Stratagy
from a local laptop/PC,
run the
Stratagy Remote software.
1.
To access the Stratagy Remote software, enter the
following from the DOS prompt (C:\).
NOTE:
If you are running
Windows,
exit Windows;
do
not use Windows' MS-DOS Prompt option.
If your local laptop uses COMl , enter:
REMOTE /n
/f
If your local laptop uses COM2, enter:
REMOTE /2
/n
/f
2.
When entered
correctly, the screen displays the
same information
as on the Stratagy
monitor
(or
would be displayed on the Stratagy monitor).
NOTE:
The screen may be blank because of the screen
saver. If so, press the
spacebar.
3.3.2
USING STRATACY LOCALLY
Both the laptop/PC
and the Stratagy system are active
simultaneously.
Use the laptop/PC as you would from the
Stratagy monitor and keyboard.
Note, however, that you
cannot upload or download
or files.
3.3.3
EXITING LOCAL ACCESS
To discontinue
local access:
1.
Be sure to leave the Stratagy system in the correct
state.
For example,
if you want Stratagy up and running
in call processing
mode,
leave Stratagy
at the
Main Menu. If you leave the Stratagy system at the
Stratagy
Configuration
Utility Menu, etc, that is
where
it will be and call processing
will not
function.
2.
Enter the following to disconnect from the Stratagy
system:
Alt
+ X
The system prompts:
OK to Exit (Y/N)
Enter Y to exit the Stratagy system.
Enter
N
to continue
accessing
the
Stratagy
system.
3.
Disconnect the null modem cable.
Advertisement
Chapters
Table of Contents
