Samsung OfficeServ SMT-i5243 User Manual page 416

Setting IP Manually
• From the "Network Mode Setup" Menu,
select [1. MANUAL IP] and press
SPEAKER. Next, press the HOLD button
twice to get to the NETWORK SETUP
MENU as seen here.
Enter the IP keyset's IP address, the net-
work's netmask and gateway as shown.
• Select the [2. IP ADDRESS SET UP]
menu and press SPEAKER, the LCD will
display this message and the user can
enter its IP address.
Check if there is any currently saved IP address of the phone on the LCD. If the IP
address has not been set, the LCD displays nothing. The user can enter the IP
address using [0]-[9] dial buttons and [,] button for entering a "." Save that IP
address by pressing the SPEAKER button. Use the HOLD button to backspace.
• Select the [3. NETMASK SET UP] menu
and press SPEAKER, the LCD will display
the following message and the user can
enter a new Netmask IP address. Use the
HOLD button to backspace.
Check if there is any currently saved subnet mask address of the phone on the
LCD. If the subnet mask address has not been set, the display will show nothing.
Press any dial buttons from [0]-[9] and [,] button to enter the subnet mask IP
address and then save that subnet mask IP address by pressing the SPEAKER but-
ton. Use the HOLD button to backspace.
• Select [4. GATEWAY SET UP] menu and
press SPEAKER, the LCD will display the
following message and the user can
enter a new gateway address.
Check if there is any currently saved Gateway IP address of the phone on the LCD.
If the gateway IP address has not been set, the LCD displays nothing.The user can
enter the gateway IP address by using [0]-[9] and [,] button and can save that IP
address by pressing the SPEAKER button. Use the HOLD button to backspace.
NOTE: In the [3. NETWORK SET UP MENU], [1. NETWORK MODE SETUP] option,
when [2. DHCP] is selected the IP address, Netmask, and Gateway will not be dis-
played on the LCD. Press HOLD to exit to Main Menu.
12
1.NETWORK MODE SET UP
2.IP ADDRESS SET UP
3.NETMASK SETUP
4.GATEWAY SETUP
INPUT IP ADDRESS & PRESS OK
xxx.xxx.xxx.xxx
INPUT NETMASK & PRESS OK
xxx.xxx.xxx.xxx
INPUT GATEWAY & PRESS OK
xxx.xxx.xxx.xxx
Load and Upgrade Set/Modify
The fourth item [4. LOAD & UPGRADE SET UP] sets or modifies the IP phone's
software version. Use extreme caution when upgrading the keyset. Only use this
if you are upgrading your IP keyset firmware.
Select the [4. LOAD & UPGRADE SET UP] item and move to the lower level. The
screen below is displayed.
1.UPGRADE TFTP SERVER
2.UPGRADE START
Select option [1. UPGRADE TFTP SERVER] and enter the IP address of the TFTP
server containing the ITP software. Use [0]-[9] and [,] button to enter the IP
address. Press SPEAKER to save.
Select option [2. UPGRADE START] and press SPEAKER to start the upgrade
process. Press HOLD to exit.
System Server Setup
From the Main Setup Menu, the fifth item [5. SYSTEM SERVER SET UP] sets or
modifies settings related to registering the phone to the main processor. You can
obtain this information from your system administrator. The screen below is dis-
played.
1.SERVER IP ADDRESS
You can set/modify the IP address of the main processor at the [1. SERVER IP
ADDRESS] item. The screen below is displayed when you enter the item. The serv-
er IP is the IP address of the main processor.
INPUT SERVER IP ADDRESS
xxx.xxx.xxx.xxx
You can confirm the current IP address of the main processor at the LCD panel.
The address is left blank if it is not set. Use the dial buttons from [0]-[9], and [,] to
set the IP address and press the SPEAKER button to save and exit. Select the [2.
SERVER ID] menu. Use the HOLD button to backspace.
INPUT SYSTEM ID
Home Page
13