Table of Contents
Advertisement
❍General Purpose Controller 6 (Controller number 81)
Status
2nd byte
BnH
51H
n = MIDI channel number:
vv = Control value:
* The Tone Level parameter (PATCH/TVA PARAMETER) of Tone 2 will change.
❍General Purpose Controller 7 (Controller number 82)
Status
2nd byte
BnH
52H
n = MIDI channel number:
vv = Control value:
* The Tone Level parameter (PATCH/TVA PARAMETER) of Tone 3 will change.
❍General Purpose Controller 8 (Controller number 83)
Status
2nd byte
BnH
53H
n = MIDI channel number:
vv = Control value:
* The Tone Level parameter (PATCH/TVA PARAMETER) of Tone 4 will change.
❍Portamento control (Controller number 84)
Status
2nd byte
BnH
54H
n = MIDI channel number:
kk = source note number:
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
BnH
5BH
n = MIDI channel number:
vv = Reverb Send Level:
* In Performance mode, the Part Reverb Send Level parameter (PERFORM/PART VIEW/
OUTPUT) will change.
❍Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
BnH
5DH
n = MIDI channel number:
vv = Chorus Send Level:
* In Performance mode, the Part Chorus Send Level parameter (PERFORM/PART VIEW/
OUTPUT) will change.
❍RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
BnH
65H
BnH
64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then Data Entry (Controller numbers
6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry
messages that is received at the same MIDI channel after that are recognized as changing
toward the value of the RPN messages. In order not to make any mistakes, transmitting
RPN Null is recommended after setting parameters you need.
This device receives the following RPNs.
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
RPN
Data entry
MSB, LSB
MSB, LSB
00H, 00H
mmH, llH
* In Performance mode, the Part Bend Range parameter (PERFORM/PART VIEW/
PITCH) will change.
00H, 01H
mmH, llH
* In Performance mode, the Part Fine Tune parameter (PERFORM/PART VIEW/PITCH)
will change.
00H, 02H
mmH, llH
* In Performance mode, the Part Coarse Tune parameter (PERFORM/PART VIEW/
PITCH) will change.
00H, 05H
mmH, llH
* Not received in Patch mode.
7FH, 7FH
---, ---
RPN and NRPN will be set as "unspecified." Once this setting has been made, subsequent
Parameter values that were previously set will not change.
●Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
pp = Program number:
* Not received in Performance mode when the Receive Program Change parameter
(PERFORM/MIDI) is OFF.
●Channel Pressure
Status
2nd byte
DnH
vvH
n = MIDI channel number:
vv = Channel Pressure:
* Not received in Performance mode when the Receive Channel Pressure parameter
(PERFORM/MIDI) is OFF.
●Pitch Bend Change
Status
2nd byte
EnH
llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
* Not received when the Tone Receive Bender parameter (PATCH/CONTROL) is OFF.
* Not received in Performance mode when the Receive Bender parameter (PERFORM/
MIDI) is OFF.
MIDI Implementation
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
Modulation Depth Range
mm, ll: 00 00H - 00 06H
(0 - 16384 x 600 / 16384 cent)
RPN null
mm, ll: ignored
0H - FH (ch.1 - 16)
00H - 7FH (prog.1 - prog.128)
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
219
Advertisement
Table of Contents
