Roland Juno-Stage User Manual page 114

Chapter 8. Detailed Editing for Patches
Parameter Value
Fade Mode
ON <, ON >,
OFF <, OFF >
Fade Mode
ZOOM
Fade Time
0–127
Fade
ZOOM
Key Trigger OFF, ON
Pitch Depth ★
-63–+63
Pitch Depth
ZOOM
TVF Depth ★
-63–+63
Filter Depth
ZOOM
TVA Depth ★
-63–+63
Amp Depth
ZOOM
Pan Depth ★
-63–+63
Pan Depth
ZOOM
Positive (+) and negative (-) settings for the Depth parameters result in differing kinds of change in pitch and volume. For example, if you set the Depth
parameter to a positive (+) value for one tone, and set another tone to the same numerical value, but make it negative (-), the modulation phase for the two
tones will be the reverse of each other. This allows you to shift back and forth between two different tones, or combine it with the Pan setting to cyclically
change the location of the sound image.
If "Struct 1 & 2, 3 & 4" (
* p. 99
tones 1 and 2 are combined into tone 2, and the outputs of tones 3 and 4 are combined into tone 4.)
How to Apply the LFO
● Apply the LFO gradually after the key is pressed
Delay
high (more)
Time Fade Time
Pitch
Cutoff Frequency
Level
Pan
Note on
low (less)
● Apply the LFO immediately when the key is pressed, and then gradually begin to decrease the effect
high (more)
Delay Time
Pitch
Cutoff Frequency
Level
Pan
Note on
low (less)
● Apply the LFO gradually after the key is released
Delay
high (more)
Time
Pitch
Cutoff Frequency
Level
Pan
Note Note
on off
low (less)
● Apply the LFO from when the key is pressed until it is released, and gradually begin to decrease the effect when the key is released
high (more)
Pitch
Cutoff Frequency
Level
Pan
low (less)
Note on
Note off
114
Explanation
How the LFO will be applied
* Set this according to your purpose as described in "How to Apply the LFO" (below).
Time over which the LFO amplitude will reach the maximum (minimum)
* Set this according to your purpose as described in "How to Apply the LFO" (below).
Specifies whether the LFO cycle will be synchronized to begin when the key is pressed (ON) or not (OFF).
How deeply the LFO will affect pitch
How deeply the LFO will affect the cutoff frequency
How deeply the LFO will affect the volume
How deeply the LFO will affect the pan
) is set to TYPE 02–10, the settings for tone 1 (3) will follow the settings of tone 2 (4). (This is because the outputs of
Depth
Fade Time
Depth
Fade Time
Depth
Delay
Time Fade Time
Depth
Parameters indicated by (
ZOOM
Parameter marked with a "★" can be controlled using specified MIDI messages.
Fade Mode: ON <
Delay Time: Time from when the keyboard is played until the LFO begins to be
applied
Fade Time: Time over which the LFO amplitude will reach the maximum after the
Delay Time has elapsed
Fade Mode: ON >
Delay Time: Time that the LFO will continue after the keyboard is played
Fade Time: Time over which the LFO amplitude will reach the minimum after the
Delay Time has elapsed
Fade Mode: OFF <
Delay Time: Time from when the keyboard is released until the LFO begins to be
applied
Fade Time: Time over which the LFO amplitude will reach the maximum after the
Delay Time has elapsed
Fade Mode: OFF >
Delay Time: Time that the LFO will continue after the keyboard is released
Fade Time: Time over which the LFO amplitude will reach the minimum after the
Delay Time has elapsed
) can be edited via ZOOM EDIT (p. 97).
(Matrix Control, p. 110)