Roland Juno-Stage User Manual page 181

50: REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to the
input sound. A tap delay is connected immediately after the reverse
delay.
fig.MFX-50
L in
Feedback
Rev
Rev. Delay
R in
Parameter Value
Threshold 0–127
Rev Delay Time 0–1300 msec, note
Rev Delay
-98–+98%
Feedback #
Rev Delay HF 200–8000 Hz,
Damp BYPASS
Rev Delay Pan
L64–63R
Rev Delay Level 0–127
Delay 1 – 3 Time 0–1300 msec, note
Delay 3 Feedback # -98–+98%
Delay HF Damp 200–8000 Hz, BYPASS
Delay 1 Pan,
L64–63R
Delay 2 Pan
Delay 1 Level,
0–127
Delay 2 Level
Low Gain -15–+15 dB
High Gain -15–+15 dB
Balance # D100:0W–D0:100W
Level 0–127
2-Band
EQ
D1
Delay
D2
D3
2-Band
EQ
Explanation
Volume at which the reverse
delay will begin to be applied
Delay time from when sound is
input into the reverse delay until
the delay sound is heard
Proportion of the delay sound
that is to be returned to the input
of the reverse delay (negative
values invert the phase)
Frequency at which the
high-frequency content of the
reverse-delayed sound will be cut
(BYPASS: no cut)
Panning of the reverse delay
sound
Volume of the reverse delay
sound
Delay time from when sound is
input into the tap delay until the
delay sound is heard
Proportion of the delay sound
that is to be returned to the input
of the tap delay (negative values
invert the phase)
Frequency at which the low-
frequency content of the tap
delay sound will be cut (BYPASS:
no cut)
Panning of the tap delay sounds
Volume of the tap delay sounds
Amount of boost/cut for the
low-frequency range
Amount of boost/cut for the
high-frequency range
Volume balance of the original
sound (D) and delay sound (W)
Output volume
51: SHUFFLE DELAY
Adds a shuffle to the delay sound, giving the sound a bouncy delay
effect with a swing feel.
fig.MFX-51
L in
Feedback
L out
Delay
R in
R out
Parameter Value
0–2600 msec,
Delay Time #
note
Shuffle
0–100
Rate #
Acceleration 0–15
Feedback #
-98–+98%
200–8000 Hz,
HF Damp
BYPASS
Pan A/B
0–127
Level A/B 0–127
Low Gain -15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance #
D0:100W
Level 0–127
Effects List
Delay A A
B
Delay B
Explanation
Adjusts the time until the delay sound is
heard.
Adjusts the ratio (as a percentage) of the
time that elapses before Delay B sounds
relative to the time that elapses before the
Delay A sounds.
When set to 100, the delay times are the
same.
Adjusts the speed which the Delay Time
changes from the current setting to its
specified new setting.
Adjusts the amount of the delay that's
feedback into the effect. Negative (-) settings
invert the phase.
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you
don't want to filter out any high frequencies,
set this parameter to BYPASS.
Stereo location of Delay A/B
Volume of delay A/B
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct sound
(D) and the effect sound (W)
Output level
2-Band
L out
EQ
2-Band
R out
EQ
181