Table of Contents
Advertisement
14:
INFINITE PHASER
A phaser that continues raising/lowering the frequency at which the
sound is modulated.
fig.MFX-14
L in
Infinite Phaser
R in
Parameter
Value
Mode
1, 2, 3, 4
Speed #
-100–+100
Resonance #
0–127
Mix #
0–127
Pan #
L64–63R
Low Gain
-15–+15 dB
High Gain
-15–+15 dB
Level
0–127
15:
RING MODULATOR
This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.
fig.MFX-15
L in
Ring Mod
2-Band EQ
R in
Ring Mod
2-Band EQ
Parameter
Value
Frequency #
0–127
Sens #
0–127
Polarity
UP, DOWN
Low Gain
-15–+15 dB
High Gain
-15–+15 dB
D100:0W–
Balance #
D0:100W
Level
0–127
Pan L
2-Band EQ
Pan R
Explanation
Higher values will produce a
deeper phaser effect.
Speed at which to raise or lower
the frequency at which the sound
is modulated
(+: upward / -: downward)
Amount of feedback
Volume of the phase-shifted
sound
Panning of the output sound
Amount of boost/cut for the
low-frequency range
Amount of boost/cut for the
high-frequency range
Output volume
L out
R out
Explanation
Adjusts the frequency at which modulation is
applied.
Adjusts the amount of frequency modulation
applied.
Determines whether the frequency
modulation moves towards higher
frequencies (UP) or lower frequencies
(DOWN).
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct sound
(D) and the effect sound (W)
Output level
16:
STEP RING MODULATOR
This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.
fig.MFX-16
L out
L in
Step Ring Mod
R in
R out
Step Ring Mod
Parameter
Value
Step 01–16
0–127
Rate #
0.05–10.00 Hz, note
Attack #
0–127
Low Gain
-15–+15 dB
High Gain
-15–+15 dB
Balance #
D100:0W–D0:100W
Level
0–127
You can use multi-effect control to make the step sequence play
again from the beginning (p. 164).
17:
TREMOLO
Cyclically modulates the volume to add tremolo effect to the sound.
fig.MFX-17a
L in
Tremolo
R in
Tremolo
Parameter
Value
TRI, SQR, SIN, SAW1,
SAW2
Mod Wave
SAW1
Rate #
0.05–10.00 Hz, note
Depth #
0–127
Low Gain
-15–+15 dB
High Gain
-15–+15 dB
Level
0–127
Effects List
2-Band EQ
L out
R out
2-Band EQ
Explanation
Frequency of ring modulation at
each step
Rate at which the 16-step sequence
will cycle
Speed at which the modulation
frequency changes between steps
Amount of boost/cut for the
low-frequency range
Amount of boost/cut for the
high-frequency range
Volume balance of the original
sound (D) and effect sound (W)
Output volume
L out
2-Band EQ
R out
2-Band EQ
Explanation
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW2
Frequency of the change
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
169
Advertisement
Table of Contents
