Table of Contents
Advertisement
MIDI Implementation
❍Expression (Controller number 11)
Status
2nd byte
BnH
0BH
n = MIDI channel number:
vv = Expression:
* Not received when Rx Expression Tone Receive Expression parameter (PATCH/MISC
or RHYTHM/RECEIVE) is OFF.
* Not received in Performance mode when Rx Expression parameter (PERFORM/MISC)
is OFF.
❍Hold 1 (Controller number 64)
Status
2nd byte
BnH
40H
n = MIDI channel number:
vv = Control value:
* Not received when Rx Hold-1/Tone Receive Hold-1 parameter (PATCH/CONTROL or
RHYTHM/RECEIVE) is OFF.
* Not received in Performance mode when Rx Hold-1 parameter (PERFORM/MISC) is
OFF.
* When the Redamper Sw parameter (PATCH/MISC) is turned ON, 128 discrete steps are
recognized for the value.
❍Portamento (Controller number 65)
Status
2nd byte
BnH
41H
n = MIDI channel number:
vv = Control value:
* In Performance mode, the Part Portamento Switch parameter (PERFORM/PART VIEW/
KEY MOD) will change.
❍Sostenuto (Controller number 66)
Status
2nd byte
BnH
42H
n = MIDI channel number:
vv = Control value:
❍Soft (Controller number 67)
Status
2nd byte
BnH
43H
n = MIDI channel number:
vv = Control value:
❍Legato Foot Switch (Controller number 68)
Status
2nd byte
BnH
44H
n = MIDI channel number:
vv = Control value:
* In Performance mode, the Part Legato Switch parameter (PERFORM/PART VIEW/KEY
MOD) will change.
❍Hold-2 (Controller number 69)
Status
2nd byte
BnH
45H
n = MIDI channel number:
vv = Control value:
* A hold movement isn't done.
❍Resonance (Controller number 71)
Status
2nd byte
BnH
47H
n = MIDI channel number:
vv= Resonance value (relative change):
* In Performance mode, the Part Resonance Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
218
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0-63 = OFF, 64-127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63),
❍Release Time (Controller number 72)
Status
2nd byte
BnH
48H
n = MIDI channel number:
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the Part Release Time Offset parameter (PERFORM/PART
VIEW/OFFSET) will change.
❍Attack time (Controller number 73)
Status
2nd byte
BnH
49H
n = MIDI channel number:
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the Part Attack Time Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍Cutoff (Controller number 74)
Status
2nd byte
BnH
4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
* In Performance mode, the Part Cutoff Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍Decay Time (Controller number 75)
Status
2nd byte
BnH
4BH
n = MIDI channel number:
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Decay Time Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍Vibrato Rate (Controller number 76)
Status
2nd byte
BnH
4CH
n = MIDI channel number:
vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Vibrato Rate parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍Vibrato Depth (Controller number 77)
Status
2nd byte
BnH
4DH
n = MIDI channel number:
vv = Vibrato Depth Value (relative change):
* In Performance mode, the Part Vibrato Depth parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍Vibrato Delay (Controller number 78)
Status
2nd byte
BnH
4EH
n = MIDI channel number:
vv = Vibrato Delay value (relative change):
* In Performance mode, the Part Vibrato Delay parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍General Purpose Controller 5 (Controller number 80)
Status
2nd byte
BnH
50H
n = MIDI channel number:
vv = Control value:
* The Tone Level parameter (PATCH/TVA PARAMETER) of Tone 1 will change.
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
Advertisement
Table of Contents
