Toshiba e-STUDIO5540C Service Manual page 507

Sub
05/08 Mode Element
element
08 Setting Process Fuser Lower limit of control
Mode temperature
(Recycled paper/low
temperature
environment)
08 Setting Process Fuser
Mode
08 Setting Process Fuser
Mode
08 Setting Process Fuser Fusing temperature
Mode during printing
(Special mode for
waterproof paper)
08 Setting Process Fuser Fusing temperature
Mode during printing
(Special mode for
waterproof paper)
08 Setting Process Fuser Fusing temperature
Mode during printing
(Special mode for
waterproof paper)
08 Setting Process Fuser Waterproof paper
Mode special mode: Heater
forced On time
08 Setting Process Fuser Waterproof paper
Mode special mode: Heater
forced On time
08 Setting Process Fuser
Mode
e-STUDIO5540C/6540C/6550C (Ver08)
Sub-
Item Subitem Code
code
5301
5315
5316
5323
5323
5323
5324
5324
5325
Default Acceptable
Details
value value
15 Press roller side/C or 6 0-18
CK mode/duplex
printing
Fusing temperature 1 0-1
correction setting
during printing (Wide
paper)
Copying speed control 0 0-1
switchover setting
0 Center of heat roller 15 0-16
2 Center of pressure 8 0-16
roller
3 Side of pressure roller 8 0-16
0 Heat roller 0 0-10
1 Press roller 5 0-10
Pre-running time for 5 0-16
first printing (Special
mode for waterproof
paper)
100
RAM Contents
M 0: 80ºC 1: 85ºC 2: 90ºC 3: 95ºC 4: 100ºC 5: 105ºC
6: 110ºC 7: 115ºC 8: 120ºC 9: 125ºC 10: 130ºC 11:
135ºC 12: 140ºC 13: 145ºC 14: 150ºC 15: 155ºC 16:
160ºC 17: 165ºC 18: 170ºC
M 0: Disabled 1: Enabled
M 0: Disabled 1: Enabled
M 0: 120ºC 1: 125ºC 2: 130ºC 3: 135ºC 4: 140ºC 5:
145ºC 6: 150ºC 7: 155ºC 8: 160ºC 9: 165ºC 10: 170º
C 11: 175ºC 12: 180ºC 13: 185ºC 14: 190ºC 15: 195
ºC 16: 200ºC
M 0: 120ºC 1: 125ºC 2: 130ºC 3: 135ºC 4: 140ºC 5:
145ºC 6: 150ºC 7: 155ºC 8: 160ºC 9: 165ºC 10: 170º
C 11: 175ºC 12: 180ºC 13: 185ºC 14: 190ºC 15: 195
ºC 16: 200ºC
M 0: 120ºC 1: 125ºC 2: 130ºC 3: 135ºC 4: 140ºC 5:
145ºC 6: 150ºC 7: 155ºC 8: 160ºC 9: 165ºC 10: 170º
C 11: 175ºC 12: 180ºC 13: 185ºC 14: 190ºC 15: 195
ºC 16: 200ºC
M 0: Invalid
1 to 10: Setting value * 1 (sec.)
M 0: Invalid
1 to 10: Setting value * 1 (sec.)
M 0: Invalid 1: 0 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5
sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 10 sec. 10: 12
sec. 11: 14 sec. 12: 16 sec. 13: 18 sec. 14: 20 sec.
15: 25 sec. 16: 30 sec.
Proce Servic
dure e UI
4
1
1
4
4
4
4
4
1