BRP Evinrude E-TEC Series Service Manual page 339

EMM CIRCUIT/SENSOR
Throttle Position Sensor
11
(TPS) out of idle range
Throttle Position Sensor
12
(TPS) circuit fault
13 TPS below range
14 TPS above range
15 ROM (EMM program)
Crankshaft Position Sensor (CPS)
16
Intermittent loss of SYNC
17 55 V circuit BELOW range
18 55 V circuit ABOVE range
19 Start-in-gear
21 Winterization activated
23 EMM Temperature Sensor circuit fault
24 EMM Temperature BELOW range
25 EMM Temperature ABOVE range
26 12 V circuit BELOW range
27 12 V circuit ABOVE range
29 EMM Temperature OVER range
31 Engine temperature OVER range
33 Critical NO OIL detected
34 Oil injection pump circuit OPEN
40 Engine Temperature ABOVE range–Low speed
41 Engine Temperature Sensor circuit fault
42 Engine Temperature BELOW range
43 Engine Temperature ABOVE range
44 Barometric Pressure (BP) Sensor circuit fault
45 BP Sensor BELOW range
46 BP Sensor ABOVE range
47 Air Temperature (AT) circuit fault
48 Air Temperature BELOW range
TIME TO
EMM LED DISPLAY
ACTIVATE
- 2 seconds
LED 3: OFF (Cranking) / ON (Running) 0.8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
- -
LED 2: OFF (Cranking)
10 instances
LED 3: ON (Running)
LED 1: ON (Running) 1 minute
LED 1: ON (Running) 1 minute
LED 3: OFF (Cranking) -
All LEDs FLASHING -
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 4: ON (Running) 8 seconds
LED 1: ON (Running) 5 minutes
LED 1: ON (Running) 5 minutes
LED 4: FLASHING 4 seconds
LED 4: FLASHING 8 seconds
LED 4: FLASHING 3 hours
LED 4: ON (Running) 4 seconds
LED 4: ON (Running) 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 4: ON (Running) 8 seconds
- 8 seconds
- 8 seconds
- 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
LED 3: OFF (Cranking) / ON (Running) 8 seconds
SENSOR: CIRCUIT VOLTAGE / RESISTANCE (Ω) / INFORMATION
TPS Voltage > 1.71 V with key ON (or cranking). Becomes stored fault when outboard starts.
When both hard and stored faults are present, check for improperly adjusted throttle cable.
TPS Voltage: < 0.14 V, or > 4.92 V. Engine limited to idle speed.
Check sensor resistance—3000 to 7000 Ω (between pins A and B ) & 4000 to 8000 Ω (between pins A and C )
TPS Voltage < 0.2 V. Check linkage and IDLE stop.
TPS Voltage > 4.85 V. Check linkage and WOT stop.
ROM "CHECKSUM" failure. Check software program number in EMM. Reload or replace with proper program.
EMM counts losses of synchronization with crankshaft sensor. Check CPS mounting and resistance. Air gap range: 00.036 to 0.110 in. (1 to 2.8 mm),
nominal 0.073 in. (1.85 mm) Resistance: 560 Ω ± 10% @ 77°F (25°C)
System Voltage < 45 V. Engine limited to 1200 RPM. Perform stator/charging tests.
System Voltage > 57 V. Engine limited to 1200 RPM. Perform stator/charging tests.
Check for loose connections in 55 V circuit.
Attempted engine start while in gear. Engine will not start.
Engine is speed limited, and stops after 360 oil pulses. Refer to Maintenance or Operator's Guide.
EMM Temperature < -71° F (-57.4° C), or > 313° F (156° C).
EMM Temperature < -22 ° F (-30° C).
EMM Temperature > 194°F (90°C). Engine limited to 1200 RPM. See Code 29.
Battery voltage < 12.5 V. Perform stator/charging tests.
Battery voltage > 15.5 V. Check battery connections and wiring.
EMM Temperature > 212° F (100° C). Engine SHUTDOWN. Will NOT restart until EMM temperature
returns to operating range. Check outboard and EMM cooling systems.
Engine Temperature > 248° F (120° C) Engine SHUTDOWN. Check cooling system.
Check temperature sensor resistance—9000 to 11000 Ω @ 77°F (25°C).
Outboard has run three hours with code 34 or 117. Engine SHUTDOWN. Will restart and run for 1 minute intervals.
Engine limited to 1200 RPM. Check oil injection pump circuit resistance—22 Ω.
Engine Temperature > 212° F (100° C) below 3500 RPM.
Engine Temperature < -15° F (-26.2° C), or > 332° F (166.5° C).
Check 5 V circuit and ground (NEG), and sensor resistance—9000 to 11000 Ω @ 77°F (25°C).
Engine Temperature < -4° F (-20° C). Check engine temperature and sensor resistance.
Engine Temperature > 194° F (90° C) above 3500 RPM
Engine limited to 1200 RPM. Check cooling system.
Pressure < 3.9 in. Hg (13.3 kPa), or > 35.1 in. Hg (119.0 kPa).
Check atmospheric condition for comparison. Clear code and retest.
Air temperature < -58° F (-49.9° C), or > 218° F (103.2° C).
Check 5 V circuit and ground (NEG), and sensor resistance—9000 to 11000 Ω @ 77°F (25°C).
EVINRUDE 15 – 30 HP EMM SERVICE CODE CHART
Pressure < 20.7 in. Hg (70 kPa).
Pressure > 31 in. Hg (105 kPa).
Air temperature < -22° F (-30° C).
Rev 01/10 page 1