Extron electronics PVS 407D User Manual page 34

Command
View horizontal start value
Set vertical start value
Increment vertical start value
Decrement vertical start value
View vertical start value
X2(
KEY: = PVT HD RGB or PVT HDMI RGB wallplate inputs (2 and 4 only)
X3@
= Horizontal start
X3#
= Vertical start
VoiceLift – VLR 302 and VLR 102
Request VoiceLift status
information (VLR 302)
View VoiceLift status
(VLR 102)
NOTES:
•
Returns E25 (device not present) when VoiceLift receiver is not detected/ present.
Example A: Rly11 Rly20 Pair11 Ver1.00.0002.
•
Switcher sends out the unsolicited responses (with tag) via Ethernet/USB/RS-232 whenever there is any state change on the VoiceLift
receiver.
X3*
= LINK slot 1
KEY:
X3(
= LINK slot 2
X4)
= Relay 1
X4!
= Relay 2
X4@
= Firmware Version
X4%
= Relay
X4^
= Contact closure input state
X4&
= VoiceLift microphone status
ASCII Command Response
(host to switcher) (switcher to host)
E X2( X3@]
HSRT}
Verbose mode 2/3
Hsrt
E X2( X3#
* VSRT} Vsrt
E X2(
+
VSRT} Vsrt
E X2(
-
VSRT} Vsrt
E X2( X3#]
VSRT}
Verbose mode 2/3
Vsrt
0-255
(default = 128)
0-255
(default = 128)
34I
Rly1
X3(
•Ver
or E25
Inf34*Rly1
Verbose mode 2/3
Pair
or Inf34*E25
X4%
34I
•
or E25
Verbose mode 2/3
Inf34
or Inf34*E25
Example B: Inf34* Rly11 Rly20 Pair11 Ver1.00.0002
0 = LINK slot 1 is not paired or pairing fails.
1 = LINK slot 1 is paired to a microphone.
9 = Microphone is on/ connected or LINK slots are occupied and cannot pair.
0 = LINK slot 2 is not paired or pairing fails.
1 = LINK slot 2 is paired to a microphone.
9 = Microphone is on/ connected or LINK slots are occupied and cannot pair.
0 = Off
0 = Off
Firmware version info with build. Example response: 1.00.0042
0 = Off
0 = Open
0 = No carrier/ microphone is off
1 = Channel A or C
X2( X3@]
*
X2( X3#]
*
X2( X3#]
*
X2( X3#]
*
X2( X3#]
*
2
= Input 2
X4) X4! X3*
•Rly2 •Pair
X4@]
]
X4) X4!
•Rly2 •
X3* X3( X4@]
•Ver
]
X4^ X4&]
•
]
X4% X4^ X4&]
*
• •
]
1 = On
1 = On
1 = On
1 = Closed
2 = Channel B or D
3 = Channels A or C and B or D
PVS 407D • SIS Communication and Control
Additional Description
X3@
View horizontal start for
X3# X2(
Set vertical start at for
Increase vertical start to
X3# X2(
for .
Decrease vertical start to
X3# X2(
for .
X3# X2(
View vertical start for
4
= Input 4
View information on VoiceLift status.
Device is not present.
Device is not present.
View information on VoiceLift status.
Device is not present.
Device is not present.
]
X2(
.
.
.
28