Extron electronics PVS 407D User Manual page 27

X3# = Vertical start
X3$ = Status
X3% = Audio output
volume
X3^ = Audio filename
NOTE: The audio file must be in specific audio format type
supported by the firmware e.g. 8.0 kHz, 16 bit mono PCM format.
= Audible Chime
X3&
X3* = LINK slot 1
= LINK slot 2
X3(
X4) = VoiceLift VLR 302
relay 1 status
X4! = VoiceLift VLR 302
relay 2 status
X4@ = VLR 302 firmware
version with build
= Feedback
X4#
suppressor
= Number of
X4$
connections
X4% = Relay status
(VLR 102)
X4^ = Contact closure
input state (VLR
102)
X4& = VoiceLift status
(VLR 102)
X10! = Default name
0-255 (default midpoint of 128 trans-
lates to the default value in the input
lookup tables)
0 = Off/disable
1 = On/enable
000 to 100, (-100 dB to 0 dB),
[default 080]
Alphanumeric, up to 32 characters (for
example, "lunchtime"):
• File name must contain
alphanumeric characters.
• Symbols, special characters and
spaces are not allowed except
underscore.
• Valid characters are A-Z, a-z, 0-9
and _ (underscore).
• The file name can start with a
number or underscore.
• It cannot end with an underscore.
0 =Off/disable
1 = On/enable (default)
E25 = Device not present/ detected
0 =LINK slot 1 is not paired to a
microphone or pairing fails
1 = LINK slot 1 is paired microphone
9 = Microphone is on/ connected or
LINK slots are occupied and
cannot pair.
0 =LINK slot 2 is not paired to a
microphone or pairing fails
1 = LINK slot 2 is paired
9 = Microphone is on/connected or
LINK slots are occupied and
cannot pair.
0 = Off
1 = On
0 = Off
1 = On
Example response: 1.00.0042
0 =Off/disable (default)
1 = On/enable
E25 = Device not present/ detected
Number of open connections
0 = Off
1 = On
0 = Open
1 = Closed
0 = No carrier/microphone is off
1 = Channel A or C
2 = Channel B or D
3 = Channels A or C and B or D
Combination of model name and last
3 hex pairs of MAC address
(for example PVS-407D-07-4B-E9)
X10@ = Verbose mode
If tagged responses are enabled, all read commands
NOTE:
return the constant string + the data, like setting the value
does. For example:
command: E CN } response: Ipn • X10^]
X10# = Baud rate
X10$ = Hardware (MAC)
address
= Unit name
X10%
X10^ = Date and time
= On/Off status
X10&
X10* = Password
user password cannot be assigned if an admin
NOTE: A
password does not exist and the switcher returns the error
code "E14". If admin password gets cleared, then user
password is also removed.
= IP address
X10(
(xxx.xxx.xxx.
] xxx)
= Subnet mask
X11)
(xxx.xxx.xxx.
xxx)
X11! = Gateway address
(xxx.xxx.xxx.
xxx)
X11@ = GMT offset
X11# = Prefix (subnet
mask bits)
PVS 407D • SIS Communication and Control
0 = Clear/none;
1 = Verbose mode
2 = Tagged responses for queries
3 = Verbose mode, tagged responses
for queries
0 = 9600 (Default)
1 = 19200
2 = 38400
3 = 115200
(00-05-A6-xx-xx-xx)
Text string up to 24 characters drawn
from the alphabet (A-Z), digits (0-9),
and hyphen (-). No blank or space
characters are permitted as part of a
name. No distinction is made between
upper and lower case. The first char-
acter must be an alpha character. The
last character must not be a hyphen.
Set local date and time format (MM/
DD/YY-HH:MM:SS) for example,
06/21/15-10:54:00.
0=off/disable; 1=on/enable
Password: maximum length is 12
characters. All human-readable
characters are permitted except "/",
"\", "|", " ", and "*". Passwords are
case-sensitive and cannot be a single
space.
Leading zeros in each of 4 fields are
optional in setting values, and are
suppressed in returned values.
Factory default IP address:
192.168.254.254
Leading zeros in each of 4 fields are
optional in setting values, and are
suppressed in returned values.
Default subnet mask: 255.255.0.0
Leading zeros in each of 4 fields are
optional in setting values, and are
suppressed in returned values.
Default gateway address: 0.0.0.0
Greenwich Mean Time (GMT) offset
value (-12:00 to 14:00).
This represents hours and minutes
(hh:mm) offset from GMT.
Subnet 255.255.0.0 is represented
as a prefix value by /16.
21