Extron electronics PVS 407D User Manual page 33

Command
Play audio file
NOTES:
•
This command responds with an E28 error (file not found) if the alphanumeric audio file does not exist.
•
This command responds with an E22 error (busy) if the audio file is not played due to low priority.
•
Only one audio file is played at a time. The firmware cannot play audio file 1 on lineout audio output and then start audio file 2 on amplified
audio output until lineout audio output finishes audio file 1.
•
Firmware sends out a "Play99" unsolicited response after an audio file is finished playing (after the file playing duration).
Play an audio file
Stop (abort) playback
View play status
X2%
= Output port to play back audio
KEY:
X2^
= Audio file playback mode
X2*
= Audio priority level
X3^
= Audio filename
Picture adjustment (PVT HD RGB and PVT HDMI RGB, inputs 2 and 4 only)
Set pixel phase value
Increment pixel phase value
Decrement pixel phase value
View pixel phase value
Set total pixel value
Increment total pixel value
Decrement total pixel value
View total pixel value
X2(
KEY: = PVT HD RGB or PVT HDMI RGB wallplate inputs (2 and 4 only)
X3)
= Pixel phase
X3!
= Total pixels
Set horizontal start value
Increment horizontal start
value
Decrement horizontal start
value
ASCII Command Response
(host to switcher) (switcher to host)
E X2% X3^ X2^
* * * Play
X2*
PLAY 99
PLAY}
E
Play 0
0 PLAY}
E 0]
PLAY}
X2%
*
1 = All
2 = Amplified audio output
3 = Lineout audio output
0 = Play once (or use to stop audio file playback).
1-300 = Play continuously (with a 0-299 second delay between repeats).
0-3, optional, 0 = least. Defaults to 0 if not specified
Alphanumeric filename (see
E X2( X3)
*
PHAS} Phas
E X2(
+
PHAS} Phas
E X2( }
-
PHAS Phas
E X2( X3)]
PHAS}
Verbose mode 2/3
Phas
E X2( X3!
* TPIX} Tpix
E X2( +
TPIX} Tpix
E X2(
-
TPIX} Tpix
E X2( X3!]
TPIX}
Verbose mode 2/3
Tpix
0-63 32
( = default)
±255 of the default value
E X2( X3@
* HSRT} Hsrt
E X2(
+
HSRT} Hsrt
E X2( -
HSRT} Hsrt
X2% X3^ X2^ X2*
]
* * *
]
]
or
X3^ X2^ X2*
]
* *
page 21
for details)
X2( X3)]
*
X2( X3)]
*
X2( X3)]
*
X2( X3)]
*
X2( X3!]
*
X2( X3!]
*
X2( X3!]
*
X2( X3!]
*
2
= Input 2
4
= Input 4
X2( X3@]
*
X2( X3@]
*
X2( X3@]
*
PVS 407D • SIS Communication and Control
Additional Description
Start audio file playback.
Unsolicited response (see Note above).
Stop audio file playback.
Audio not playing.
Audio currently playing.
X3) X2(
Set pixel phase for .
X3)
Increase pixel phase to for
X3)
Decrease pixel phase to for
X3) X2(
View pixel phase for
X3! X2(
Set total pixels for .
X3!
Increase total pixels to for
X3!
Decrease total pixels to for
X3! X2(
View total pixels for .
X3@ X2(
Set horizontal start at for
Increase horizontal start to
X3@ X2(
for .
X3@
Decrease horizontal start to
X2(
.
X2(
.
X2(
.
.
X2(
.
X2(
.
.
for
27