Hitachi SJ Series User Manual page 103

Chapter 9 Chapter 9
Set-up procedure up procedure
STOP STOP
H: Motor control H: Motor control
HA- -01 Auto-tuning selection tuning selection
HA-02 02 In auto-tuning tuning . .
00: RUN key (Operator keypad) 00: RUN key (Operator keypad) 00: RUN key (Operator keypad)
HA- -03 Online-tuning selection tuning selection
S-Menu Menu oFW
STOP STOP
H: Motor control H: Motor control
Hb102 Hb102 First IM motor capacity . . motor capacity . . motor capacity . .
S-Menu Menu oFW
Example1) Change [Hb103] First Example1) Change [Hb103] First IM motor pole Change [Hb103] First
number number
Set-up procedure up procedure
Hb103
00 2P
01 4P
02 6P
03 8P
H: Motor control H: Motor control
Hb102 First IM motor capacity . . First IM motor capacity . . First IM motor capacity . .
L02
M1
00: Disabled 00: Disabled
00: Disabled 00: Disabled
0.00Hz Next group
L02
M1
5.50kW 5.50kW
1:4P
60.00Hz 60.00Hz
Next group
0.00Hz
IM motor pole
5.50kW
0:2P
60.00Hz
Action Action
3.3 Parameters of "H: Motor control" are displayed. Parameters of "H: Motor control" are displayed. Parameters of "H: Motor control" are displayed. Parameters of "H: Motor control" are displayed. Parameters of "H: Motor control" are displayed.
Using the Using the up and down up and down (
check parameters. Pressing the F2(2) key jumps check parameters. check parameters.
to the top [Hb102] of the next group of [HA]. to the top [Hb102] of the next group of [HA]. to the top [Hb102] of the next group of [HA]. to the top [Hb102] of the next group of [HA]. to the top [Hb102] of the next group of [HA].
(Tips) (Tips)
You can jump to the top parameter of the sub You can jump to the top parameter of the sub You can jump to the top parameter of the sub You can jump to the top parameter of the sub-group in You can jump to the top parameter of the sub
the group the group ([HA], [Hb], etc. in the case of group H) ([HA], [Hb], etc. in the case of group H) ([HA], [Hb], etc. in the case of group H) ([HA], [Hb], etc. in the case of group H)
using the F2(2) key (transition is performed in one using the F2(2) key (transition is performed in one using the F2(2) key (transition is performed in one using the F2(2) key (transition is performed in one using the F2(2) key (transition is performed in one
direction). direction).
Example of group H: ⋯->HA-
Example of group H: Example of group H:
3.4 Using the up and down Using the up and down ( Using the up and down
check parameters. Choose the parameter to check parameters. check parameters.
change, and then press the SEL(O) change, and then press the SEL(O) change, and then press the SEL(O) change, and then press the SEL(O) key.
Example1) Example1) [Hb103] The parameter to change the first [Hb103] The parameter to change the first [Hb103] The parameter to change the first [Hb103] The parameter to change the first [Hb103] The parameter to change the first
IM motor pole number IM motor pole number IM motor pole number. To 3.5.
Example2) Example2) [Hb104] The parameter to change the first [Hb104] The parameter to change the first [Hb104] The parameter to change the first [Hb104] The parameter to change the first [Hb104] The parameter to change the first
IM motor base frequency IM motor base frequency IM motor base frequency. To 3.6.
Action Action
3.5 If the number of If the number of motor poles is 2, using the If the number of
and down ( and down ( ) keys, adjust it to ) keys, adjust it to "00 2P", and
then press the F2(Save) key. then press the F2(Save) key. then press the F2(Save) key. then press the F2(Save) key.
(Tips) (Tips)
Data is saved when the F2(2) key is pressed. It is still Data is saved when the F2(2) key is pressed. It is still Data is saved when the F2(2) key is pressed. It is still Data is saved when the F2(2) key is pressed. It is still Data is saved when the F2(2) key is pressed. It is still Data is saved when the F2(2) key is pressed. It is still
saved even after the device is turned off. When saved even after the device is turned off. When saved even after the device is turned off. When saved even after the device is turned off. When saved even after the device is turned off. When
configuring an item, the entire screen changes to the configuring an item, the entire screen changes to the configuring an item, the entire screen changes to the configuring an item, the entire screen changes to the configuring an item, the entire screen changes to the
screen for setting the item. When screen for setting the item. screen for setting the item.
setting after changing it, press the F1(Back) ke setting after changing it, press the F1(Back) ke setting after changing it, press the F1(Back) key. The setting after changing it, press the F1(Back) ke setting after changing it, press the F1(Back) ke
screen returns to the parameter list display screen returns to the screen returns to the
3.6 To confirm To confirm if the data is correctly changed, check if the data is correctly changed, check if the data is correctly changed, check if the data is correctly changed, check if the data is correctly changed, check
the lower section of the parameter display. Press the lower section of the parameter display. Press the lower section of the parameter display. Press the lower section of the parameter display. Press the lower section of the parameter display. Press the lower section of the parameter display. Press
the F1(1) key three times to return to the monitor. the F1(1) key three times to return to the monitor. the F1(1) key three times to return to the monitor. the F1(1) key three times to return to the monitor. the F1(1) key three times to return to the monitor.
9-8
Operating Instructions Operating Instructions Operating Instructions Operating Instructions
) keys, you can , you can
Pressing the F2(2) key jumps Pressing the F2(2) key jumps Pressing the F2(2) key jumps
->Hb->HC->Hd >Hd->HA->⋯
) keys, you can , you can
Choose the parameter to Choose the parameter to
key.
. To 3.6.
poles is 2, using the up poles is 2, using the
"00 2P", and
When not saving ing the
parameter list display parameter list display.
group in
⋯