Firstech CM-7000 Master Manual page 48

CM7 Master Guide
FO2 - On: this option will provide a FAD output on both data and analog connections, when the
user taps the unlock/disarm once to silence the Compustar system while it's sounding, so it will disarm
any factory alarm that may be sounding as well. In case the FAD function unlocks the doors the CM7 will
send the FAA on both data and analog connections 5 seconds later to make sure the vehicle is
re-locked and secure. (This feature works well with GM, Chrysler, Dodge, Jeep, Toyota, Lexus vehicles
that may have factory security.)
FO3 – Disarm with 1 press: This option will allow the user to completely disarm the system once it is
sounding on the first unlock command. When set to this option the CM will unlock and send the FAD
commands on the first disarm/unlock press from a Firstech remote.
3-16 RPS: (Remote Paging Sensor) this feature sets the RPS hardware being used with the CM7.
FO1 - RPS Touch: (default) this option enables the RPS touch functions when using the RPS touch
hardware with the CM7. RPS can be used to arm/lock and disarm/unlock a CM7 or page a Firstech
remote or accessory. Please refer the RPS section of this manual or the RPS product manual for
installation and operation of the RPS touch hardware.
FO2 - RPS II: (knock sensor) This option enables the RPS II functions when using the RPS II hardware
with the CM7. RPS can be used to arm/lock and disarm/unlock a CM7 or page a Firstech remote or
accessory. Please refer the RPS section of this manual or the RPS product manual for installation and
operation of the RPS II hardware.
FO3 - RPS Touch NO LED FLASH WHILE ARMED: This option enables the RPS touch functions
when using the RPS touch hardware with the CM7 but the LED WILL NOT FLASH WHILE ARMED.
RPS can be used to arm/lock and disarm/unlock a CM7 or page a Firstech remote or accessory. Please
refer the RPS section of this manual or the RPS product manual for installation and operation of the
RPS touch hardware.
4-01 Aux 1 Output: This feature determines the duration of the auxiliary 1 output. (Option 4 allows the
output duration to be set for a specific length of time 1-99 sec. and 1-15 min (with OP500 update only)
(Specific time setting only available when using the OP500)
FO1 - 500mS: This option will provide a (-) negative output for 500 milliseconds (Half second)
output on any POC programmed with setting 10 (AUX 1)
FO2 - Latched: This option will provide a latched (-) negative output on any POC programmed with
setting 10 (AUX 1). Note: This will stay latched until AUX 1 command is sent again to
shut it off.
FO3 - 500mS pulse + programmable timed output: this option will provide a (-) negative output for
500 milliseconds (0.5 seconds) output on any POC programmed with setting 10 (AUX
1). It will pause for 250 milliseconds then provide a timed output (based off feature 4-01 option
4). Note: to program the timed output, the user must change feature 4-01 to option 4, then adjust AU1
(AUX programmable output time) to desired time. To complete the programming steps, feature 4-01
must be changed to option 3. I.e. 0.5 second pulse...pause...10 second pulse, this option can be used to
roll windows up or down on a vehicle that requires a similar action using the driver's door key
cylinder.
FO4 - Program: This option allows the AUX output time to be programmed for a duration between
1-99 seconds. Note: with an OP500 update there will be additional time duration between 1-15
minutes available.
Copyright 2016 Fi rstech ,
LLC.
Alarm and Starter System
www.firstechdata.com
Page 48