Roland SoundCanvas SC-88 Pro Owner's Manual page 92

<RT (Rotary)>
RT L Slow (RT Low Frequency Slow Rate)
Adjust the speed of the low-range rotor for the low-
speed (Slow) setting.
RT L Fast (RT Low Frequency Fast Rate)
Adjust the speed of the low-range rotor for the high-
speed (Fast) setting.
RT Lo Accl (RT Low Frequency Acceleration)
Adjust the time over which the rotation speed of the
low-range rotor will change from low-speed to high-
speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Lo Lev (RT Low Frequency Level) 0 - 127 [9]
Adjust the volume of the low-range rotor.
RT H Slow (RT High Frequency Slow Rate)
Adjust the speed of the high-range rotor for the low-
speed (Slow) setting.
RT H Fast (RT High Frequency Fast Rate)
Adjust the speed of the high-range rotor for the
high-speed (Fast) setting.
RT Hi Accl (RT High Frequency Acceleration)
Adjust the time over which the rotation speed of the
high-range rotor will change from low-speed to
high-speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Hi Lev (RT High Frequency Level)
Adjust the volume of the high-range rotor.
RT Sept (RT Separation)
Adjust the spread of the rotary sound.
#RT Speed
Simultaneously switch the rotational speed of both
the low-range and the high-range rotors.
Slow : Slow down the rotation to the speci-
fied speeds (RT L Slow parameter /
RT H Slow parameter values).
Fast : Speed up the rotation to the specified
speeds (RT L Fast parameter / RT H
Fast parameter values).
90
RT Pan (RT Output Pan)
0.05 - 10.0 [6]
RT Level
Level (Output level )
0.05 - 10.0 [7]
64: PH / AutoWah (Phaser, Auto-wah)
0 - 15 [8]
This connects a Phaser effect and an Auto-wah effect
in parallel.
<PH (Phaser)>
0.05 - 10.0 [10]
PH Man (Phaser Manual)
+PH Rate (Phaser Rate)
0.05 - 10.0 [11]
PH Depth (Phaser Depth)
0 - 15 [12]
PH Reso (Phaser Resonance)
PH Mix (Phaser Mix Level)
0 - 127 [13]
PH Pan (Phaser Output Pan)
0 - 127 [14]
PH Level (Phaser Level)
Slow/Fast [15]
<AW (Auto-wah)>
AW Filter (Auto-wah Filter Type)
AW Sens (Auto-wah Sensitivity)
Chapter 4. Insertion Effects
Adjust the stereo position of the rotary sound. L63
is far left, 0 is center, and R63 is far right.
Adjust the volume of the rotary sound.
Adjust the output level.
L Phaser
R
Auto Wah
Adjust the center frequency at which the phaser
sound will be modulated.
Adjust the modulation speed of the phaser.
Adjust the modulation depth of the phaser.
Adjust the emphasis for the region around the cen-
ter frequency specified by the PH Man parameter.
Adjust the proportion of the phase-shifted sound
that will be mixed with the direct sound.
Set the stereo location of the phaser sound. L63 is
far left, 0 is center, and R63 is far right.
Adjust the volume of the phaser sound.
Select the type of filter for the auto-wah.
LPF : The wah effect will be produced over
a broad frequency range.
BPF : The wah effect will be produced over
a narrow frequency range.
Adjust the sensitivity with which the auto-wah filter
will be modulated.
L63 - 0 - R63 [18]
0 - 127 [19]
0 - 127 [20]
[11H, 08H]
Pan
Pan
100 - 8.0k [1]
0.05 - 10.0 [2]
0 - 127 [3]
0 - 127 [4]
0 - 127 [5]
L63 - 0 - R63 [16]
0 - 127 [17]
LPF/BPF [6]
0 - 127 [7]