Roland SoundCanvas SC-88 Pro Owner's Manual page 84

CF Depth
Adjust the depth of modulation for the chorus or
flanger.
CF Fb (CF Feedback)
Adjust the amount (%) of the flanger sound that will
be returned to the input. Negative (-) values will
invert the phase.
In the case of Chorus, this will have no effect.
CF Mix
Adjust the volume of the chorus or flanger sound.
<Dly (Delay)>
Dly Time (Delay Time)
Adjust the time from the original sound until when
the delay sound is heard.
Dly Fb (Delay Feedback Level)
Adjust the amount of the delay sound that is
returned to the input.
#Dly Mix (Delay Mix)
Adjust the volume of the delay sound.
Level (Output level )
Adjust the output level.
53: Bass Multi
Bass Multi provides Compressor (Cmp), Overdrive or
Distortion (OD), Equalizer (EQ), and Chorus or
Flanger (CF) effects connected in series.
L
Cmp
OD
R
<Cmp (Compressor)>
Cmp Atck (Compressor Attack)
Adjust the time over which the sound will rise after it
is input.
Cmp Sus (Compressor Sustain)
Adjust the time over which low-level sounds are
boosted until they reach a specified volume.
Increasing the value will shorten the time. When the
value is modified, the level will also change.
Cmp Level (Compressor Level)
Adjust the volume of the compressor sound.
Cmp Sw (Compressor Switch)
Turn the compressor on/off.
82
0 - 127 [14]
-98% - +98% [15]
0 - 127 [16]
0m - 635m [17]
0 - 127 [18]
0 - 127 [19]
0 - 127 [20]
[04H, 05H]
EQ CF
0 - 127 [1]
0 - 127 [2]
0 - 127 [3]
Off/On [4]
Chapter 4. Insertion Effects
<OD (Overdrive/Distortion)>
OD Sel (ODSelect)
Select either bass guitar Overdrive or Distortion.
+OD Drive (OD Drive)
Adjust the depth of distortion. The volume will
change together with the depth of distortion.
OD Amp (OD Amp Simlation Type)
Select the type of guitar amp
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
OD Amp Sw (OD Amp Switch)
Turn OD Amp on/off.
OD Sw (OD Switch)
Turn Overdrive/Distortion on/off.
<EQ (Equalizer)>
EQ L Gain (EQ Low Gain)
Adjust the low-range gain of the equalizer.
EQ M Fq (EQ Mid Frequency)
Set the center frequency for the equalizer mid-
range.
EQ M Q (EQ Mid Q)
Adjust the width of the area centered at the EQ M
Fq setting in which the gain will be affected. The
area affected will become narrower as this value is
increased.
EQ M Gain (EQ Mid Gain)
Adjust the gain of the area specified by the EQ M
Fq parameter and the EQ M Q parameter.
EQ H Gain (EQ High Gain)
Adjust the high-range gain of the equalizer.
<CF(Chorus/Flanger)>
CF Sel (CF Select)
Select either Chorus or Flanger.
CF Rate
Adjust the speed of modulation for the chorus or
flanger.
CF Depth
Adjust the depth of modulation for the chorus or
flanger.
CF Fb (CF Feedback level)
Adjust the amount (%) of the flanger sound that will
be returned to the input. Negative (-) values will
invert the phase.
In the case of Chorus, this will have no effect.
Odrv/Dist [5]
0 - 127 [6]
Small/BltIn/2-Stk [7]
Off/On [8]
Off/On [9]
-12 - +12 [10]
200 - 6.3k [11]
0.5/1.0/2.0/4.0/9.0 [12]
-12 - +12 [13]
-12 - +12 [14]
Chorus/Flangr [15]
0.05 - 6.40 [16]
0 - 127 [17]
-98% - +98% [18]