Roland SoundCanvas SC-88 Pro Owner's Manual page 80

RT H Fast (RTRT High Frequency Fast Rate)
Adjust the speed of the high-range rotor for the
high-speed (Fast) setting.
RT Hi Accl (RT High Frequency Accelaration)
Adjust the time over which the rotation speed of the
high-range rotor will change from low-speed to
high-speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Hi Lev (RT High Frequency Level)
Adjust the volume of the high-range rotor.
RT Sept (RT Separation)
Adjust the spatial spread of the rotary sound.
#RT Speed
Simultaneously switch the rotational speed of both
the low-range and the high-range rotors.
Slow : Slow down the rotation to the speci-
fied speeds (RT L Slow parameter /
RT H Slow parameter values).
Fast : Speed up the rotation to the specified
speeds (RT L Fast parameter / RT H
Fast parameter values).
Level (Output level )
Adjust the output level.
48: GTR Multi 1 (Guitar Multi1)
Guitar Multi 1 connects Compressor (Cmp), Overdrive
or Distortion (OD), Chorus or Flanger (CF), and Delay
(Dly) effects in series.
L
Cmp
OD
R
<Cmp (Compressor)>
Cmp Atck (Compressor Attack)
Adjust the time over which the sound will rise after
input.
Cmp Sus (Compressor Sustain)
Adjust the time over which low-level sounds are
boosted until they reach a specified volume.
Increasing the value will shorten the time. When the
value is modified, the level will also change.
Cmp Level (Compressor Level)
Adjust the volume of the compressor sound.
Cmp Sw (Compressor Switch)
Turn the compressor on/off.
78
0.05 - 10.0 [13]
0 - 15 [14]
0 - 127 [15]
0 - 127 [16]
Slow/Fast [17]
0 - 127 [20]
[04H, 00H]
CF Delay
0 - 127 [1]
0 - 127 [2]
0 - 127 [3]
Off/On [4]
Chapter 4. Insertion Effects
<OD (Overdrive/Distortion)>
OD Sel (OD Select)
Select either Overdrive or Distortion.
+OD Drive
Adjust the depth of distortion. The volume will
change together with the depth of distortion.
OD Amp (OD Amp Simulator Type)
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
OD Amp Sw (OD Amp Switch)
Turn OD Amp on/off.
OD L Gain (OD Low Gain)
Adjust the low-range gain.
OD H Gain (OD High Gain)
Adjust the high-range gain.
OD Sw (OD Switch)
Turn Overdrive or Distortion on/off.
<CF (Chorus/Flanger)>
CF Sel (CF Select)
Select either Chorus or Flanger.
CF Rate
Adjust the speed of modulation
CF Depth
Adjust the depth of modulation.
CF Fb (CF Feedback)
Adjust the amount (%) of the flanger sound that is
returned to the input. Negative (-) values will invert
the phase.
In the case of Chorus, this will have no effect.
CF Mix
Adjust the volume of the chorus or flanger sound.
<Dly(Delay)>
Dly Time (Delay Time)
Adjust the time from the original sound until when
the delay sound is heard.
Dly Fb (Delay Feedback Level)
Adjust the amount of the delay sound that is
returned to the input.
#Dly Mix (Delay Mix)
Adjust the volume of the delay sound.
Level (Output level )
Adjust the output level.
Odrv/Dist [5]
0 - 127 [6]
Small/BltIn/2-Stk/3-Stk [7]
Off/On [8]
-12 - +12 [9]
-12 - +12 [10]
Off/On [11]
Chorus/Flangr [12]
0.05 - 6.40 [13]
0 - 127 [14]
-98% - +98% [15]
0 - 127 [16]
0m - 635m [17]
0 - 127 [18]
0 - 127 [19]
0 - 127 [20]