Roland SoundCanvas SC-88 Pro Owner's Manual page 77

Hi Gain (High gain )
Adjust the high frequency gain.
Level (Output level )
Adjust the output level.
42: EH Flanger (Enhancer
This effect connects an enhancer and a flanger in
series.
L Enhancer
R
Enhancer
+EH Sens (Enhancer Sensitivity )
Adjust the sensitivity of the enhancer.
EH Mix (Enhancer Mix level )
Adjust the ratio with which the overtones generated
by the enhancer are combined with the direct
sound.
FL Dly (Flanger pre delay )
Adjust the time delay from when the direct sound
begins until the flanger sound is heard.
FL Rate (Flanger rate )
Adjust the modulation speed of the flanger effect.
FL Depth (Flanger depth )
Adjust the modulation depth of the flanger effect.
FL Fb (Flanger Feedback level ) -98% - +98% [9]
Adjust the proportion (%) of the flanger sound that
is fed back into the effect. Negative (-) settings will
invert the phase.
#FL Bal (Flanger balance)
Adjust the volume balance between the sound
which passes through the flanger and the sound
which does not. With a setting of D>0E, only the
enhancer sound will be output, and with a setting of
D 0<E, the enhancer sound which passes through
the flanger will be output. "D" and "E" respectively
indicate D (dry sound) and E (effect sound) values
of 100.
Low Gain
Adjust the low frequency gain.
Hi Gain (High gain )
Adjust the high frequency gain.
Level (Output level )
Adjust the output level.
43: EH Delay (Enhancer
This effect connects an enhancer and a delay in
series.
-12 - +12 [18]
0 - 127 [20]
Flanger)
[02H, 07H]
EQ
Flanger Balance
EQ
0 - 127 [1]
0 - 127 [2]
0 - 100m [6]
0.05 - 10.0 [7]
0 - 127 [8]
D> 0E - D 0<E [10]
-12 - +12 [17]
-12 - +12 [18]
0 - 127 [20]
Delay) [02H, 08H]
Chapter 4. Insertion Effects
L
Enhancer
R Enhancer
+EH Sens (Enhancer Sensitivity )
Adjust the sensitivity of the enhancer.
EH Mix (Enhancer Mix level )
Adjust the ratio with which the overtones generated
by the enhancer are combined with the direct
sound.
Dly Time (Delay time )
Adjust the time delay from when the direct sound
begins until the delay sound is heard.
Dly Fb (Delay feedback level )
Adjust the proportion (%) of the delay sound that is
fed back into the delay input. Negative (-) settings
will invert the phase.
Dly HF (Delay HF damp )
Adjust the frequency above which delayed sound
fed back to the delay input will be cut. If you do not
wish to cut the high frequencies of the delay feed-
back, set this parameter to Bypass.
#Dly Bal (Delay balance )
Adjust the volume balance between the sound
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
enhancer sound will be output, and with a setting of
D 0<E, the enhancer sound which passes through
the delay will be output.
"D" or "E" on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain
Adjust the low frequency gain.
Hi Gain (High gain )
Adjust the high frequency gain.
Level (Output level )
Adjust the output level.
44: Cho Delay (Chorus
This effect connects a chorus and a delay unit in
series.
L
Chorus
R
Cho Dly (Chorus pre delay )
Adjust the time delay from when the direct sound
begins until the chorus sound is heard.
EQ
Balance
Delay
EQ
0 - 127 [1]
0 - 127 [2]
0 - 500m [6]
-98% - +98% [7]
315 - 8k/Bypass [8]
D> 0E - D 0<E [10]
-12 - +12 [17]
-12 - +12 [18]
0 - 127 [20]
Delay) [02H, 09H]
EQ
Delay
EQ
0 - 100m [1]
75