Roland SoundCanvas SC-88 Pro Owner's Manual page 63

Pre Filter (Pre filter type)
Select the type of filter.
Off : a filter will not be used
LPF : cut the frequency range above the
Cutoff parameter
HPF : cut the frequency range below the
Cutoff parameter
Cutoff (Cutoff frequency)
Adjust the basic frequency of the filter.
Pre Dly (Pre delay time)
Adjust the time delay from when the direct sound
begins until the processed sound is heard.
+Rate
Adjust the rate of modulation.
Depth
Adjust the depth of modulation.
#Feedback (Feedback level)
Adjust the amount (%) of the processed sound that
is returned (fed back) into the input. Negative (-)
settings will invert the phase.
Phase
Adjust the spatial spread of the sound.
Balance (Effect balance)
Adjust the volume balance between the direct and
the processed sound.
" D" or "E" on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain
Adjust the gain of the low frequency range.
Hi Gain (High Gain)
Adjust the gain of the high frequency range.
Level (Output level)
Adjust the output level.
11: Step Flanger
The Step Flanger is an effect in which the flanger pitch
changes in steps.
L
Flanger
Flanger
R
Pre Dly (Pre delay time)
Adjust the time delay from when the direct sound
begins until the processed sound is heard.
Rate
Adjust the rate of modulation.
Off/LPF/HPF [1]
250 - 8k [2]
0 - 100m [3]
0.05 - 10.0 [4]
0 - 127 [5]
-98% - +98% [6]
0 - 180 [7]
D> 0E - D 0<E [16]
-12 - +12 [17]
-12 - +12 [18]
0 - 127 [20]
[01H, 24H]
EQ
Balance
EQ
0 - 100m [1]
0.05 - 10.0 [2]
Chapter 4. Insertion Effects
Depth
Adjust the depth of modulation.
+Feedback (Feedback level)
Adjust the amount (%) of the processed sound that
is returned (fed back) into the input. Negative (-)
settings will invert the phase.
Phase
Adjust the spatial spread of the sound.
#Step Rate
Adjust the rate (period) of pitch change.
Balance (Effect balance)
Adjust the volume balance between the direct and
the processed sound.
"D" or "E" on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain
Adjust the gain of the low frequency range.
Hi Gain (High gain)
Adjust the gain of the high frequency range.
Level (Output level)
Adjust the output level.
12: Tremolo
Tremolo cyclically modulates the volume to add tremo-
lo effect to the sound.
Tremolo
L
R Tremolo
Mod Wave (Modulation wave)
Select the type of modulation.
Tri : The sound will be modulated like a
triangle wave.
Sqr : The sound will be modulated like a
square wave.
Sin : The sound will be modulated like a
sine wave.
Saw1,2 : The sound will be modulated like a
sawtooth wave. The "teeth" in Saw1
and Saw2 point at opposite direc-
tions.
Saw1
+Mod Rate (Modulation rate)
Adjust the speed of modulation.
#Mod Depth (Modulation depth)
Adjust the depth of modulation.
0 - 127 [3]
-98% - +98% [4]
0 - 180 [5]
0.05 - 10.0 [6]
D> 0E - D 0<E [16]
-12 - +12 [17]
-12 - +12 [18]
0 - 127 [20]
[01H, 25H]
EQ
EQ
Tri/Sqr/Sin/Saw1/Saw2 [1]
Saw2
0.05 - 10.0 [2]
0 - 127 [3]
61