Roland SoundCanvas SC-88 Pro Owner's Manual page 198

Address(H) Size(H) Data(H)
40 03 00 00 00 02 00 - 7F
40 03 01#
40 03 03 00 00 01 00 - 7F
40 03 04 00 00 01 00 - 7F
40 03 05 00 00 01 00 - 7F
40 03 06 00 00 01 00 - 7F
40 03 07 00 00 01 00 - 7F
40 03 08 00 00 01 00 - 7F
40 03 09 00 00 01 00 - 7F
40 03 0A 00 00 01 00 - 7F
40 03 0B 00 00 01 00 - 7F
40 03 0C 00 00 01 00 - 7F
40 03 0D 00 00 01 00 - 7F
40 03 0E 00 00 01 00 - 7F
40 03 0F 00 00 01 00 - 7F
40 03 10 00 00 01 00 - 7F
40 03 11 00 00 01 00 - 7F
40 03 12 00 00 01 00 - 7F
40 03 13 00 00 01 00 - 7F
40 03 14 00 00 01 00 - 7F
40 03 15 00 00 01 00 - 7F
40 03 16 00 00 01 00 - 7F
* Reading EFX TYPE and EFX PARAMETER please refer to page 56, 176
Address(H) Size(H) Data(H)
40 03 17 00 00 01 00 - 7F
40 03 18 00 00 01 00 - 7F
40 03 19 00 00 01 00 - 7F
40 03 1B 00 00 01 00 - 7F
40 03 1C 00 00 01 00 - 7F
40 03 1D 00 00 01 00 - 7F
40 03 1E 00 00 01 00 - 7F
40 03 1F 00 00 01 00 - 7F
* EFX TYPE is a macro parameter which sets various Insertion Effect parameters as a group. When you use EFX TYPE to select an Insertion Effect type, the various effect
parameters will be set to appropriate values.
* In MODE-2 (Double module mode), EFX SEND TO DELAY and EFX SEND EQ SWITCH cannot be used.
* In the case of Mode 2 (Double Module mode), the Insertion effect cannot be used for Parts with a CHANNEL MSG RX PORT (page 194) setting of PORT B.
Patch Part parameters
This unit has 16 Parts in Group A and 16 Parts in Group B. Parameters that can be set individually for each Part are called Patch Part parameters.
If you use exclusive messages to set Patch Part parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel).
The Block number can be specified as one of 16 blocks, from 0(H) to F(H).
To specify a Part of group A, use the Block number corresponding to the Part and specify an address of 40 ** ** via PORT A (normally MIDI IN A).
To specify a Part of group B, use the Block number corresponding to the Part and specify an address of 40 ** ** via PORT B (normally MIDI IN B).
To specify a Part of either group A or B from a single PORT, specify an address of 40 ** ** for group A Parts or an address of 50 ** ** for group B Parts when using PORT A.
Conversely, to specify a Part of either group A or B from PORT B, specify an address of 50 ** ** for group A Parts or an address of 40 ** ** for group B Parts. In other words,
when specifying Parts of the opposite side as the PORT being used, use addresses 50 ** **.
The relation between Part number and Block number is as follows.
x...BLOCK NUMBER (0 - F), Part 1
Part 2
:
Part 9
Part10
Part11
Part12
:
Part16
n... MIDI channel number (0 - F) of the BLOCK.
In the following map, the control numbers of the control changes are indicated as CC#.
Address(H) Size(H) Data(H)
40 1x 00 00 00 02 00 - 7F
40 1x 01# 00 - 7F
40 1x 02 00 00 01 00 - 10
40 1x 03 00 00 01 00 - 01
40 1x 04 00 00 01 00 - 01
40 1x 05 00 00 01 00 - 01
40 1x 06 00 00 01 00 - 01
40 1x 07 00 00 01 00 - 01
40 1x 08 00 00 01 00 - 01
40 1x 09 00 00 01 00 - 01
40 1x 0A 00 00 01 00 - 01
* When "General MIDI System On" is received, Rx. NRPN will be set OFF. When "GS Reset" is received, it will be set ON.
196
Parameter
EFX TYPE
EFX PARAMETER 1
EFX PARAMETER 2
EFX PARAMETER 3
EFX PARAMETER 4
EFX PARAMETER 5
EFX PARAMETER 6
EFX PARAMETER 7
EFX PARAMETER 8
EFX PARAMETER 9
EFX PARAMETER 10
EFX PARAMETER 11
EFX PARAMETER 12
EFX PARAMETER 13
EFX PARAMETER 14
EFX PARAMETER 15
EFX PARAMETER 16
EFX PARAMETER 17
EFX PARAMETER 18
EFX PARAMETER 19
EFX PARAMETER 20
Parameter
EFX SEND LEVEL TO REVERB [Pro] 0-127
EFX SEND LEVEL TO CHORUS [Pro] 0-127
EFX SEND LEVEL TO DELAY
EFX CONTROL SOURCE1
EFX CONTROL DEPTH1
EFX CONTROL SOURCE2
EFX CONTROL DEPTH2
EFX SEND EQ SWITCH
(default MIDIch = 1) x=1
(default MIDIch = 2) x=2
: :
(default MIDIch = 9) x=9
(default MIDIch =10) x=0
(default MIDIch =11) x=A
(default MIDIch =12) x=B
: :
(default MIDIch =16) x=F
Parameter
TONE NUMBER
Rx. CHANNEL
Rx. PITCH BEND
Rx. CH PRESSURE(CAf)
Rx. PROGRAM CHANGE
Rx. CONTROL CHANGE
Rx. POLY PRESSURE(PAf)
Rx. NOTE MESSAGE
Rx. RPN
Rx. NRPN
Chapter 8. Appendix
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
[Pro]
Description
[Pro] 0-127
[Pro] Off, CC1-95, CAf, Bend
[Pro] -100 - 0 - +100 [%]
[Pro] Off, CC1 - 95, CAf, Bend
[Pro] -100 - 0 - +100 [%]
[Pro] OFF/ON
Description Default Value (H)
CC#00 VALUE 0 - 127 00
P.C. VALUE 1 - 128 00
1 - 16, OFF
OFF / ON 01
OFF / ON 01
OFF / ON 01
OFF / ON 01
OFF / ON 01
OFF / ON 01
OFF / ON 01
OFF / ON 00(01*)
Default Value (H) Description
00 00 00: Thru
Default Value (H) Description
28 40
00 0
00 0
00 Off
40 0 (%)
00 Off
40 0 (%)
01 ON
Description
0
1
Same as the Part Number
ON
ON
ON
ON
ON
ON
ON
OFF(ON*)